Lin Yi-Feng

Dr. Lin Yi-Feng

Department of Electronic and Computer Engineering, National Taiwan University of Science and Technology
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2022 in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
Verified
Journal Article
Closed access
JLJing-Yuan Lin
Jing-Yuan Lin
HYHsuan-Yu Yueh
Hsuan-Yu Yueh
LYLin Yi-Feng
Lin Yi-Feng
LPLiu pin-hsien
Liu pin-hsien
The LLC resonant converter has been widely used in the power supply industry, such as server power, TV power, and adapter, because this converter can realize the zero-voltage switching (ZVS) at the power MOSFETs of the primary side. Thus, the switch losses can be decreased, and the conversion efficiency can also be improved. The electric vehicle (EV) charger has been recently widely used in research and development. However, designing LLC resonant converters for the wide battery voltage range is difficult because this converter is usually utilized in pulse frequency modulation (PFM) to regulate the output voltage. This converter will also be limited on the low operating frequency range for the high conversion efficiency due to the switching frequency. By contrast, the phase-shift modulation (PSM) control for the wide output voltage range has been used at LLC resonant converters. However, the ZVS will be lost due to the lagging leg of the LLC resonant converter when the phase-shift angle is remarkably excessive. The burst-mode control has also been proposed for the converter to regulate the output voltage and maintain high conversion efficiency at light-load conditions. Therefore, this paper utilized the combination of PFM, PSM and burst-mode control for the LLC resonant converter operating at the wide output voltage range for EV charge applications. Furthermore, this paper proposed a synchronous rectification advance on-time control for PFM control, which can help address the ZVS at the lagging leg when the phase-shift angle is excessive. Detailed analysis and design of this control method are also described. The performance evaluation of the proposed LLC resonant converter with hybrid control was finally realized under the following conditions: 3.75 kW, DC input voltage of 400 VDC, DC output voltage of 75–475 VDC and maximum conversion efficiency around 97%.

9 May 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
JLJing-Yuan Lin
Jing-Yuan Lin
LPLiu pin-hsien
Liu pin-hsien
HYHsuan-Yu Yueh
Hsuan-Yu Yueh
LYLin Yi-Feng
Lin Yi-Feng
The LLC converter has been widely used in the power supply industry for its high conversion efficiency. When the output load is low, the LLC resonant converter will substantially increase the operating frequency, thereby reducing the conversion efficiency and exceeding the limited operating frequency of the specification. Thus, burst-mode control is applied to increase the ability of regulation at light-load conditions. Even so, the switching period of power-switches still occurs at a high switching frequency. Burst-mode control will also result in an extremely low-frequency output voltage ripple. In this study, a valley switching control (VSC) for the LLC resonant converter at light-load conditions is proposed. The VSC control strategy maintains the output voltage by modulating the pulse-width signals of drivers, and achieves valley switching by modulating the switching frequency. Thus, the VSC strategy can reduces the operating frequency compared with the frequency modulation strategy. Compared with burst-mode operations, the proposed VSC effectively reduces the switching loss and has the advantages of the high-frequency output voltage ripple. The VSC increases the efficiency and the power quality of the converter. Detailed analysis and design of the proposed method are described. Experimental results are recorded for a prototype converter with a DC input voltage of 400-VDC, an output voltage of 48-VDC, and an output current of 12.5-A.

11 February 2022 in Energies
Verified
Journal Article
Open access
PDF file
JLJing-Yuan Lin
Jing-Yuan Lin
HYHsuan-Yu Yueh
Hsuan-Yu Yueh
LYLin Yi-Feng
Lin Yi-Feng
LPLiu pin-hsien
Liu pin-hsien
This study presents the topology of a three-phase LLC resonant converter with matrix transformers. The three-phase LLC resonant converter has the advantages of conventional LLC resonant converters, including zero-voltage switching at the primary side, zero-current switching at the secondary side, high-frequency feasibility, and high efficiency. Moreover, it has additional advantages that differ from conventional LLC, including low output capacitor current ripple, natural current sharing in three resonant currents, and a high power level. As a result of the above mentioned characteristics, LLC topology has been used in many electric vehicle charging systems, server power systems, and other high-power applications. However, as the power level becomes higher and higher, the input voltage is usually too high to reduce conduction loss, and the output current also increases. This situation makes transformer design more difficult. The increasing current means more core and copper loss, and the heat dissipation of the transformer becomes more difficult. Matrix transformer technology can improve this problem directly and simply. By utilizing matrix transformers, which are primary series connected and secondary parallel connected, the primary voltage stress and secondary current stress of the transformers can be reduced, and the output current can be distributed. The analysis of the proposed converter in this study includes a circuit operation introduction, a time-domain analysis, calculation of the transfer ratio curve in the frequency domain, and a loss analysis. The theoretical analysis and performance of the proposed converter are verified. A three-phase LLC resonant converter with matrix transformers prototype is built with a high input voltage of 800-VDC and high output current of 200-A. The output voltage is 100-VDC. The waveform and efficiency data will be shown in the experimental results.

26 April 2021 in Energies
Verified
Journal Article
Open access
PDF file
JLJing-Yuan Lin
Jing-Yuan Lin
KCKuan-Hung Chen
Kuan-Hung Chen
LPLiu pin-hsien
Liu pin-hsien
HYHsuan-Yu Yueh
Hsuan-Yu Yueh
LYLin Yi-Feng
Lin Yi-Feng
Recently, three-phase series-resonant converters (SRCs) have been proposed for high power applications. Three-phase SRCs can achieve zero-voltage-switching (ZVS) of the primary power switches and regulate the output voltage by pulse-frequency modulation. The interleaving technique is also a conventional method for DC-DC converters to achieve a high power level, reducing the output voltage ripples due to operating out of phase at the same frequency between the two converters. However, an interleaved three-phase SRC cannot easily synchronize switching instants between the two modules due to the component tolerances of circuits. In the proposed control method, phase shift modulation (PSM) is used to solve the output current imbalance caused by component tolerances. The power switches of the converter can also maintain synchronizing switching instants between the two modules. Therefore, the lower output voltage ripple can be achieved. A detailed analysis and design of this new control method for interleaved three-phase SRCs are described. Finally, prototype converters with a 2.4 kW total output were built and successfully tested to verify the feasibility of the current sharing modulation.

11 December 2024 in IEEE Access
Verified
Journal Article
Open access
JLJing-Yuan Lin
Jing-Yuan Lin
CCChuan-Ting Chen
Chuan-Ting Chen
LYLin Yi-Feng
Lin Yi-Feng
The application of a traditional boost converter requires a wide duty cycle for high boost voltage gain. The wide duty cycle has the problem of a high current peak due to a large input current. The Coupled inductor based boost converter achieves a high step-up voltage ratio and reduce the problem of wide duty cycle. However, the basic coupled inductor converters have some disadvantages. Such as high voltage spike on the switch caused by a leakage inductance and the problem of large input current still cannot effectively improve. This paper aims to address these problems. The proposed topology used a coupled inductor to achieve high step-up voltage ratio. The designed voltage stabilizing capacitor loop reduces the current peak value of the main coupling inductor. Active clamping is used to suppress voltage spikes and implement zero-voltage switching (ZVS) of the switch to improve efficiency. This study describes the working principle and time domain analysis of this topology. Detailed design of components and propose the best design process. A prototype converter with an output power of 400 W was constructed. Conducted at a DC input voltage of 40 VDC and a DC output voltage of 400 VDC. Experimental results show that the maximum conversion efficiency is 94.6%.

25 April 2024 in Energies
Verified
Journal Article
Open access
PDF file
SCSheng-Hua Chen
Sheng-Hua Chen
CCChuan-Ting Chen
Chuan-Ting Chen
LYLin Yi-Feng
Lin Yi-Feng
Many applications, such as photovoltaic systems, uninterruptible power supplies, and automobile headlamps, need a high step-up DC–DC converter without isolation. The conventional boost converter has the advantages of simple topology and easy control. However, it has some shortcomings, such as insufficient step-up voltage ratio and poor efficiency when operating at large duty-cycle conditions. One of the popular topologies used to overcome these problems is the coupled-inductor boost converter. It utilizes the turn ratio of the coupled inductor to realize a higher step-up voltage ratio. The drawback is that the leakage inductance of the coupled inductor causes a huge voltage spike when the power switches are turned off. Moreover, because coupled inductors are characterized by their large volume and high profile, a conventional coupled-inductor boost converter is unsuited for photovoltaic systems, such as the solar microinverter. This study proposes a novel high-step-up boost converter to solve these problems. This proposed converter uses dual coupled inductors instead of the conventional coupled-inductor boost converter. The secondary side of the coupled inductor is connected in series to increase the step-up voltage ratio. The proposed converter utilizes active clamping to achieve zero-voltage switching (ZVS) for suppressing voltage spike and improving conversion efficiency. In addition, low-profile designs can be fulfilled easily for solar microinverters. The proposed converter and its control method are introduced. The operation principle, circuit characteristics, and circuit analysis are presented. A prototype converter with 300 W output power 25–40 VDC input voltage and 200 VDC output voltage was tested. All functions, including high step-up voltage ratio, ZVS, and active clamping, were achieved, and the highest efficiency was around at 94.7%.