Metal coating can provide fiber Bragg grating (FBG) effective protection and improve the FBG sensor’s performance in harsh environments. However, the metalizing can impact the optical properties of the FBG. As a result, the sensor accuracy of FBG will lower. The reason for the effect is the stress produced in the metalizing. In this study, we coated the FBG by the electroless-electroplating method. The common changes of the FBG’s spectrum after the metalizing were apparent side-lobes and reduced peak loss, and the hysteresis error for temperature sensor was more than 3.5°C. To reduce the deformation of the FBG’s spectrum in the metalizing, we analyzed the origin of stress, calculated the FBG’s refractive index perturbation due to the thermal stress, and simulated the spectrums of FBG under different stress distributions. On the basis of this, we developed a stress control technology. After using the technology, the optical properties of the metal-coated fiber Bragg gratings have been retained, and their hysteresis errors for temperature sensors were less than 1.5°C. The results showed good repeatability. The study can be used for regulating metalizing processes, and for providing valuable information for metalizing other optical fiber devices.
Lamb wave (LW) is well suited for structural health monitoring (SHM) in advanced composites. However, characteristic differences between the symmetric modes and the anti-symmetric modes often add complexity to SHM systems. The anisotropic nature of composite materials, on the other hand, necessitates direction-sensitive sensing. In this paper we report the experimental demonstration of bidirectional (0° and 90°), bimodal (S0 and A0) LW measurement within the frequency range of 20–140 kHz using a polarization-maintaining fiber Bragg grating (PM-FBG) sensor attached to a composite laminated plate. By selectively interrogating the fast and/or the slow axis of the PM-FBG, we show that not only can the sensor respond to LWs propagating along both directions, but the response can also be used to differentiate the two directions. Moreover, the fast axis of the sensor is able to respond to both the S0 and the A0 modes when the sensor is aligned with the wave propagation direction, whereas single S0 mode response can be achieved with the slow axis operating perpendicularly to the wave propagation direction. Such diverse responses indicate the potential of PM-FBGs as versatile multi-parameter SHM detectors, which can effectively address the challenges posed by material anisotropicity and LW mode diversity.
We proposed a novel long-period fiber grating (LPFG) capable of simultaneously coupling cladding modes with different azimuthal orders. A theoretical model of an LPFG with asymmetric refractive index modulation (RIM) was developed in a single-mode fiber to investigate the effects of cross-sectional distribution and modulation depth on the coupling efficiency of cladding modes. Unlike conventional fabrication methods, a novel CO2 laser-based point-shaped exposure technique was introduced to induce asymmetric RIM, enabling the simultaneous coupling of the LP15 and LP06 mode within a single grating. The proposed LPFG leverages the resonance wavelength difference between the two cladding modes for sensing applications. Experimental results demonstrated effective suppression of torsion sensitivity, achieving a minimal value of 1.2 pm/(rad/m) over a twist rate range of –34.5 rad/m to 34.5 rad/m. Additionally, the LPFG reduced sensitivity to temperature and refractive index while exhibiting a high curvature sensitivity of 13.34 nm/m-1 over a curvature range of 0 to 3.88 m-1. The combination of reduced cross-sensitivities, high curvature sensitivity, and compact structure highlights the potential of the proposed LPFG for practical sensing applications in complex environments.
The assessment of fastener tightness is essential for ensuring the safety and dependability of fastener assemblies. Monitoring the preloading of an embedded screw in a confined space poses challenges, as most existing sensors are unsuitable for this purpose. This study introduces a new sensor system based on a suspended-Fiber Bragg Grating (FBG). A slender tail of an optical FBG sensor was affixed to the monitored structure, which was subjected to periodic impulse excitation. This excitation generated a multi-harmonic vibration response containing information about the tightness, resulting in a multi-frequency acoustic-elastic wave traveling along the suspended-optical fiber and being captured by the FBG sensor. Following signal extraction, a combined approach utilizing adaptive Mel Frequency Cepstral Coefficient (MFCC) feature extraction and a Probabilistic Neural Networks (PNN) classifier was proposed to detect screw loosening. By optimizing the parameters, an average accuracy of exceeding 99.7% was achieved. This study presents a valuable technique for monitoring loosening, particularly in fastener structures with embedded tiny torque screws in confined spaces.
The flagship monthly journal of SPIE, Optical Engineering (OE) publishes peer-reviewed papers reporting on research and development in all areas of optics, photonics, and imaging science and engineering.
15 February 2022 in IEEE Photonics Technology Letters
A nested partially Negative Curvature Antiresonant Hollow-Core Fiber (NC-AHCF) is numerically investigated. The fiber cladding has multiple reflective layers and no transverse nodes, which is aiming at reducing leakage losses. Moreover, the single mode operation with high purity can be obtained through the double resonant phase-matched coupling. The FOMs of $LP^{x}_{01}$ and $LP^{y}_{01}$ mode can reach 2547 and 22596, respectively.