Over the past two decades, magnetoelectric (ME) composites and their devices have been an important topic of research. Potential applications ranging from low-power sensing to high-power converters have been investigated. This review, first begins with a summary of multiferroic materials that work at room temperature. Such ME materials are usually in composites, and their ME effect generated as a product property of magnetostrictive and piezoelectric composite layers. After that, mechanisms, working principles, and applications of ME composites from heterostructural uncooled magnetic sensors, energy harvesters to highly efficient power converters will be discussed. First, the development of ME sensors in terms of materials and structures to enhance their sensitivities and to reduce noise level is reviewed and discussed. Second, the structure of ME-based energy harvesters is discussed and summarized. Third, the development of ME gyrators is summarized for power applications, including current/voltage conversion, power efficiency, power density and figures of merit. Results demonstrate that our ME gyrator has the ability to satisfy the needs of power conversion with superior efficiency (>90%), offering potential uses in power electronic applications.
Magneto-elasto-electric (ME) coupling heterostructures, consisting of piezoelectric layers bonded to magnetostrictive ones, provide for a new class of electromagnetic emitter materials on which a portable (area ~ 16 cm2) very low frequency (VLF) transmitter technology could be developed. The proposed ME transmitter functions as follows: (a) a piezoelectric layer is first driven by alternating current AC electric voltage at its electromechanical resonance (EMR) frequency, (b) subsequently, this EMR excites the magnetostrictive layers, giving rise to magnetization change, (c) in turn, the magnetization oscillations result in oscillating magnetic fields. By Maxwell’s equations, a corresponding electric field, is also generated, leading to electromagnetic field propagation. Our hybrid piezoelectric-magnetostrictive transformer can take an input electric voltage that may include modulation-signal over a carrier frequency and transmit via oscillating magnetic field or flux change. The prototype measurements reveal a magnetic dipole like near field, demonstrating its transmission capabilities. Furthermore, the developed prototype showed a 104 times higher efficiency over a small-circular loop of the same area, exhibiting its superiority over the class of traditional small antennas.
An enhancement in the power-conversion-efficiency (η) of a magneto-electric (ME) gyrator has been found by the use of Mn-substituted nickel zinc ferrite. A trilayer gyrator of Mn-doped Ni0.8Zn0.2Fe2O3 and Pb(Zr,Ti)O3 has η = 85% at low power conditions (∼20 mW/in3) and η ≥ 80% at high power conditions (∼5 W/in3). It works close to fundamental electromechanical resonance in both direct and converse modes. The value of η is by far the highest reported so far, which is due to the high mechanical quality factor (Qm) of the magnetostrictive ferrite. Such highly efficient ME gyrators with a significant power density could become important elements in power electronics, potentially replacing electromagnetic and piezoelectric transformers.
We characterized the magnetomechanical conversion abilities of Ni-Zn ferrite, cobalt ferrite, and Metglas by constructing a magnetic power path with two winding coils. We found that under high power drive, a portion of the mechanical power re-transformed to the magnetic form and was captured by the receiver coil, which resulted in a decrease in the magnetomechanical conversion ability of the coil-magnetostriction structure. This presents an upper limit of the power conversion characteristics of magnetoelectric gyrators. Furthermore, the efficiency of a Metglas/Pb(Zr,Ti)O3 gyrator was characterized by varying the values of the resistive load, magnetic bias, and power density. The maximum measured efficiency for the power transferred across an optimal resistor load was greater than 90% under low drive conditions and 89% with a power density of up to 30 W/in.3
13 June 2018 in IEEE Transactions on Industrial Electronics
Magnetoelectric (ME) gyrators are unique circuit elements capable direct conversion of current to voltage or vice versa. In order to understand power conversion and loss processes in the gyrators, an equivalent input loss factor has been developed based on Mason's model (equivalent circuit model). This factor serves to understand the loss transferring mechanism and to evaluate the conversion efficiency for the electric power in ME gyrators. Studies have been carried out for modeling the power conversion in both the solenoid and the ME core. Several important factors have been proposed and discussed to enhance conversion efficiencies in the electric-magnetic-mechanical three-phase conversion process. A simplification of our equations reveal that the efficiency of the ME gyrator is related to the product of the effective coupling (k2eff,m) and mechanical quality (Qmech). According to our model, magnetic and electric materials with high keff,m and Qmech values are the key ingredients to enhance the efficiency of ME gyrators. We have successfully realized a power efficiency of 92% based on a Metglas/hard-PZT ME gyrator, which showed a good correlation to the predicted values.
14 March 2018 in Physica Status Solidi (RRL) – Rapid Research Letters