Due to the poor thermal properties of conventional thermal fluids such as water, oil and ethylene glycol, small solid particles are added to these fluids to enhance heat transfer. Since the viscosity change determines the rheological behavior of a liquid, it is very important to examine the parameters affecting the viscosity. Since the experimental viscosity measurement is expensive and time-consuming, it is more practical to estimate this parameter. In this study, CuO (copper oxide) nanoparticles were produced and then Scanning Electron Microscope (SEM) images analyses of the produced particles were made. Nanofluids were obtained by using pure water, ethanol and ethylene glycol materials together with the produced nanoparticles and the viscosity values were calculated by experimental setups at different density and temperatures. For the viscosity values of nanofluids, predictive models were created by using different computational intelligence methods. Mean square error (MSE), root mean square error (RMSE) and mean absolute percentage error (MAPE) error analyses were used to determine the accuracy of the predictive models. The multilayer perceptron method, which has the least error value in computational methods, was chosen as the best predicting method. The multilayer perceptron method, with an average accuracy of 51%, performed better than the alternating decision tree method. As a result, the viscosity increased with the increase in the pH of the nanofluids produced by adding CuO nanoparticles and decreased with the increase in the temperature of the nanofluids. The importance of this study is to create a predictive model using computational intelligence methods for viscosity values calculated with different pH values.
In drying systems, the examination of the drying rate values of the food product in advance gives important information about the raw material to be dried. In this study, thin-layer drying behavior of apple slices in a convective solar dryer was investigated. The experiments were carried out at a drying air temperature of 46–63 °C and a drying air speed of 0.7–1.8 m/s. In order to determine the drying kinetics, the mass change of apple slices was recorded under all drying air conditions. The effects of drying air temperature and speed, drying speed of apple slices, dimensionless moisture content, were investigated. In a solar drying system, thermal efficiency, solar radiation and air velocity values were measured. The drying kinetics of 15-mm thick apple slices were examined for three days in the solar drying system. Using the decision tree algorithm, which is a machine learning algorithm, a predictive model was created for moisture rate in drying experiments and four linear equations were obtained. According to obtained equations, the collector in the drying system depends on the inlet–outlet temperature values, the drying room inlet–outlet temperature values, the drying room humidity values and air velocity values. Moisture rate data were applied to twelve different models and their performance was determined by root mean square error (RMSE) analysis. The mathematical model with the least error rate was (RMSE: 0.09) Midilli model. A comparison was made between these drying models in the literature and the model generated by the decision tree algorithm. According to the results of RMSE error analysis, it was shown that the model created with the decision tree algorithm predicted the moisture rate values with less error values RMSE: 0.03) than the Midilli model.
6 October 2021 in Biomass Conversion and Biorefinery
In this study, poppy oil and canola oil were subjected to acid and base catalysed transesterification reactions and biodiesel fuels were obtained. In addition, tests of the additive-free state of standard diesel fuel and biodiesel were also performed for comparison. These fuels have been subjected to performance and emission tests in a direct injection three-cylinder diesel engine. These values are compared with the values of standard diesel fuel. According to the results obtained from engine tests, the biodiesel produced with poppy, canola oil, and nanoparticle additives generally showed similar properties with diesel fuel. In terms of volume, the increase in the biodiesel ratio in diesel fuel has been found to increase the specific fuel consumption and exhaust outlet temperature values. By using biodiesel-containing fuels, compared to diesel fuel, CO, HC, smoke emissions decreased, NOx, CO2, and O2 increased. Biodiesel fuel samples with additives were obtained by adding a new type of CuO nanoparticle produced in the study to biodiesel-containing fuels. Comparison of the biodiesel samples and the fuel created by adding nanoparticles to these samples with the addition of nanoparticles, it has made a great contribution in the desired direction in the consumption of approximately 20% CO, 27% HC, 29% smoke (soot), and 16% specific fuel consumption. As an innovation to the literature, improvement in combustion and performance characteristics of biodiesel with nanoparticle additive, decrease in emission values and positive effect of this decrease on the environment were observed as a result of the study.
5 December 2024 in Journal of Thermal Analysis and Calorimetry