The translation of unparalleled efficiency from the lab-scale devices to practical-scale flexible modules affords a huge performance loss for flexible perovskite solar cells (PSCs). The degradation is attributed to the brittleness and discrepancy of perovskite crystal growth upon different substrates. Inspired by robust crystallization and flexible structure of vertebrae, herein, we employ a conductive and glued polymer between indium tin oxide and perovskite layers, which simultaneously facilitates oriented crystallization of perovskite and sticks the devices. With the results of experimental characterizations and theoretical simulations, this bionic interface layer accurately controls the crystallization and acts as an adhesive. The flexible PSCs achieve the power conversion efficiencies of 19.87% and 17.55% at effective areas of 1.01 cm2 and 31.20 cm2 respectively, retaining over 85% of original efficiency after 7000 narrow bending cycles with negligible angular dependence. Finally, the modules are assembled into a wearable solar-power source, enabling the upscaling of flexible electronics.
Recently, self-healing polymers have been introduced into perovskite systems to repair the grain boundary cracks and interfacial delamination caused by bending and stretching cycles. However, self-healing polymers usually require external light, heat, and moisture stimuli to be active. In addition, self-healing polymers typically have poor electrical conductivity and are prone to forming insulated grain boundaries and interfaces, which will limit the effective extraction and transport of charge carriers. Herein, we designed a self-healing ionic conductive elastomer (ICE) containing imidazolium-based ionic liquids and incorporated it into perovskite films, which effectively repaired grain boundary cracks at room temperature (∼25 °C) and reduced the potential difference between the grains and grain boundaries of the films. The stable power conversion efficiency (PCE) of the ICE-containing rigid and flexible PSCs were 25.47% and 24.84%, which are the highest efficiencies reported among all flexible perovskite solar cells (PSCs). In addition, the corresponding devices maintained more than 90% of their initial efficiency after 5000 h in a N2 glove box. Importantly, after 10 000 bending cycles (5 mm bending radius) of the ICE-containing flexible PSCs at room temperature (∼25 °C) for 1 h, the device performance can recover from 50% (before recovery: 12.43%) to 91% (after recovery: 22.59%) of the initial PCE (24.84%). This strategy will promote the development of flexible wearable electronics.
In a flexible perovskite solar cell, the bottom interface between perovskite and the electron-transporting layer is critical in determining its efficiency and reliability. High defect concentrations and crystalline film fracturing at the bottom interface substantially reduce the efficiency and operational stability. In this work, a liquid crystal elastomer interlayer is intercalated into a flexible device with the charge transfer channel toughened by the aligned mesogenic assembly. The molecular ordering is instantly locked upon photopolymerization of liquid crystalline diacrylate monomers and dithiol-terminated oligomers. The optimized charge collection and the minimized charge recombination at the interface boost the efficiency up to 23.26% and 22.10% for rigid and flexible devices, respectively. The liquid crystal elastomer-induced suppression of phase segregation endows the unencapsulated device maintaining >80% of the initial efficiency for 1570 h. Moreover, the aligned elastomer interlayer preserves the configuration integrity with remarkable repeatability and mechanical robustness, which enables the flexible device to retain 86% of its original efficiency after 5000 bending cycles. The flexible solar cell chips are further integrated into a wearable haptic device with microneedle-based arrays of sensors to demonstrate a pain sensation system in virtual reality.
The in situ polymerization controlled growth of perovskites has been demonstrated as a general strategy to effectively repair grain boundary defects. However, the highly active, volatile, and brittle cross-linked scaffolds of small molecular monomers simultaneously limit the efficiency and mechanical endurance of perovskite solar cells (PSCs). Here, we first adopt macromonomer poly(ethylene glycol)dimethacrylate (PEGDMA) to achieve an effective in situ cross-linking polymerization for flexible PSCs. PEGDMA can chemically anchor at the grain boundaries during thermal annealing of perovskite films, thus effectively regulating the crystallization and reducing grain boundary defects. In addition, the in situ cross-linking of PEGDMA can limit the thermal expansion of perovskites during thermal annealing, which releases the residual strain to enhance the mechanical stability of the perovskite film. Overall, the power conversion efficiency (PCE) of the rigid and flexible PSCs with PEGDMA reaches 23.15% and 21.41%, respectively, retaining over 90% of the initial PCE after 3500 h of storage in a glove box. Furthermore, the efficiency retention of the PSCs is maintained at more than 86% after 5000 bending cycles (bending radius: 5 mm), which is of great significance for the practical application of PSCs in portable and wearable electronics.
1 July 2024 in Journal of the American Chemical Society