The interaction between asphalt binder and aggregate is fundamental to ensure adequate performance of asphalt mixtures, mainly in the presence of water. The work of adhesion generated between both materials directly affects the resistance of asphalt mixture to moisture damage, because it measures the ease with which water can displace asphalt binder from the aggregate surface. The objective of this study was to characterize the bond strength between asphalt and several aggregate sources. A PG 64-22 neat binder was modified with several additives to determine the effect on adhesion: polymers, nanomaterials, and adhesion promoters. To measure the strength of adhesion, the bitumen bond strength (BBS) test and contact angle measurements between asphalt binder and the aggregate surface by means of goniometry were used. The surface energy of the asphalt and the aggregate, with and without the presence of water, was estimated also. Testing was performed on all binders and on each binder–aggregate combination after ( a) rolling thin-film oven (RTFO) aging and ( b) RTFO and pressure aging vessel aging. The BBS results identified differences in bond strength as a result of moisture conditioning and aging. The differences depended on the aggregate source and binder type. Different failure modes were also observed (i.e., cohesive, adhesive). The results also indicated an increase in strength of adhesion associated with the aging process: the main resistance gain was observed after RTFO aging. Finally, changes in bond strength were compared with functional composition changes associated with the aging process and related to changes in performance.
29 March 2017 in Road Materials and Pavement Design
The quality of the bitumen–aggregate interface formed in an asphalt mixture is dictated by the physicochemical properties of both materials, such as surface polarity. In order to better understand the role of polarity on interfacial adhesion between bitumen and aggregate, a systematic study was conducted by designing bitumens with different polarities. These bitumens were produced by the addition of diatoms and hydrophobic diatoms in varying concentrations. It was found that by manipulating the polarity of bitumen it is possible to design materials that result in bitumen–aggregate pairs that are more compatible with each other and resistant to debonding. On the other hand, basicity of aggregates is also highly related to obtaining asphalt mixtures with improved durability. The findings from this paper help advance the fundamental understanding of the adhesive behaviour between bitumens and aggregates. More importantly, these findings can be used to design optimal anti-strip agents for using in different asphalt mixtures.
29 March 2017 in Road Materials and Pavement Design
This study focuses on morphological changes and micromechanical properties of bitumen and its components (maltenes and asphaltenes) under neat, laboratory short- and long-term, and long-term field ageing. The material was analysed by means of atomic force microscopy in pulsed force mode, allowing for material nano-mechanical measurements. It was concluded that the colloidal equilibrium of asphalt fractions is affected by a significant loss of low molecular weight components, and air oxidising the bitumen. In addition, stiffness and adhesion were measured for each condition. It was observed that the greatest contribution in stiffness is associated with polar components, while the adhesiveness is associated mainly with non-polar components. Finally, to relate the ageing process to chemical changes, Fourier transform infrared spectroscopy measurements were performed to quantify the functional groups associated with oxidation. Furthermore, thermodynamic analysis by means of differential scanning calorimetry was performed to explain some of the observed changes in micromechanical behaviour.
The environmental impact of road construction and rehabilitation can be associated with the increase of greenhouse gas (GHG) emissions, which are highly related to climate change. Consequently, departments of transportation have recently focused on the development and implementation of tools to evaluate the performance of projects and minimize GHG emissions. An example is the use of life cycle assessment (LCA) to analyze and quantify the environmental impact of a product, system, or process, from cradle to grave. In this regard, the present case study quantifies the carbon footprint associated with the construction of the La Abundancia–Florencia highway, located in the province of San Carlos in Costa Rica. The analysis is also intended to generate consciousness both in the public and private sectors on the environmental impacts of road construction. After an LCA study, it was determined that the construction of the hot mix asphalt (HMA) layer generates a carbon footprint of 65.8 kg of CO2e per km of road. In addition, it was evident that HMA production generates the greatest environmental impact, among all the considered LCA production and construction stages, with a GHG contribution of 38% to 39% from bitumen only. Consequently, special attention to HMA production is required in order to minimize GHG emissions.
1 November 2016 in Construction and Building Materials