Multiaxial fatigue of the components is a very complex behavior. This analyzes the multiaxial fatigue failure mechanism, reviews and compares the advantages and disadvantages of the classic model. The fatigue failure mechanism and fatigue life under multiaxial loading are derived through theoretical analysis and formulas, and finally verified with the results of multiaxial fatigue tests. The model of multiaxial fatigue life for low-cycle fatigue life prediction model not only improves the prediction accuracy of the classic model, but also considers the effects of non-proportional additional hardening phenomena and fatigue failure modes. The model is proved to be effective in low-cycle fatigue life prediction under different loading paths and types for different materials. Compared with the other three classical models, the proposed model has higher life prediction accuracy and good engineering applicability.

In nano-precision surface finishing of engineering materials using MCF (magnetic compound fluid) slurry, the water-based MCF slurry is preferable from the viewpoint of the environmental issue and the running cost of cleaning workpiece and equipment. However, the uncoated-CIPs (carbonyl-iron-powders) within the conventional MCF slurry have low ability against aqueous corrosion, leading to the performance deterioration and working life shortening of the conventional MCF slurry. This study proposed a new MCF slurry containing ZrO₂-coated CIPs instead of the uncoated CIPs. Its performance in the polishing of oxygen-free copper was compared experimentally with that of the conventional one. The results showed that the work-surface finish polished with the new slurry was in the same level as that with the conventional one when the slurry was used soon after prepared, i.e., the settling time was 0 min; however, as the settling time increased the uncoated-CIPs got rusty, leading to a deterioration in the slurry performance. By contrast, no rust was observed on ZrO₂-coated CIPs even the settling time reached several days, indicating the employment of ZrO₂-coated CIPs prolonged the working-life of the MCF slurry greatly.

A mesoporous polypyrrole/MXene (mPM) composite with multi-layer sandwich-like structures was developed via molecular self-assembly templated by block copolymer micelles, enhancing dielectric loss for superior electromagnetic wave absorption.

A one-step hydrothermal method is reported for synthesizing carbon spheres (Cs) with sucrose as the carbon resource for the anode materials in lithium-ion batteries (LIBs). Firstly, the influences of synthesis temperature and time on particle size and the morphology of the Cs were researched. Then, modified carbon spheres (MCs) were synthesized with some surfactants, such as hexadecyl trimethyl ammonium bromide (CTAB) and polyvinyl alcohol (PVA). Finally, nano-sized MCs with an average diameter of 70 nm, owning the smooth surface and uniform spherical morphology systematically investigated by X-ray diffraction (XRD), scanning electron microscope (SEM), and transmission electron microscope (TEM). The outstanding performances of nano-sized MCs synthesized with PVA were demonstrated as anode materials in LIBs. The higher initial discharge capacity of 1180 mAhg⁻¹ and the excellent discharge capacity of 470 mAhg⁻¹ were obtained respectively at 100 mAg⁻¹ (0.27 C) over 50 cycles. The nano-sized MCs has also shown remarkable performance of rate capability of 284.6 mAhg⁻¹ at 1.5 C. In addition, the cycling reversibility of the nano-sized MCs is more stable than that of the sub-micron sized MCs modified with CTAB and no surfactant respectively.

Elliptical elements are essential optical surfaces for modifying optical systems. For polishing the whole elliptical surface using doughnut-shaped MCF polishing tool with variable tilt angle, an experimental investigation was conducted in this work. Firstly, a flat workpiece was polished to determine the polishing feasibility. It was found that the middle portion of the polishing tool had optimal ability to remove materials, and the surface roughness S_a at the material removal peak was changed from 134 nm to 17.5 nm within 50 min of polishing. A smoother surface could be obtained using MCF2 slurry and MCF3 slurry, but the use of MCF1 slurry resulted in a rough surface. Then, the effects of working gap h, revolution speed of MCF polishing tool and polishing time on the polishing results were tested to study the polishing characteristics. S_a 9.6 nm and glossiness 278 Gu were obtained, and form error improved from 2.3 μm to 1.3 μm. Finally, the MCF polishing tool was dried to observe the microstructure of the MCF polishing tool after polishing. Abrasive particles were distributed evenly after polishing. It was seen that the abrasive particles were grabbed by the ferric clusters, and the α-celluloses were interleaved between the clusters.