Nur Tantiyani Ali Othman

Dr. Nur Tantiyani Ali Othman


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 December 2018 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Buthainah Ali AL-TimimiButhainah Ali AL-Timimi
Buthainah Ali AL-Timimi
STSiti Masrinda Tasirin
Siti Masrinda Tasirin
PAPayam Aminayi
Payam Aminayi
ZYZahira Yaakob
Zahira Yaakob
NONur Tantiyani Ali Othman
Nur Tantiyani Ali Othman
WNWadhah Noori
Wadhah Noori
Porous Ni, Ni-Co, Ni-Fe, and Ni-Cu magnetic alloys with a morphology similar to a giant barrel sponge were synthesized via a facile co-precipitation procedure and then by hydrogen reduction treatment. For the first time, the non-supported alloys with their unique morphology were employed in catalytic biogas decomposition (CBD) at a reaction temperature of 700 °C and 100 mL min−1 to produce syngas and carbon bio-nanofilaments, and the catalysts’ behavior, CH4 and CO2 conversion, and the carbon produced during the reaction were investigated. All of the equimolar alloy catalysts showed good activity and stability for the catalytic biogas decomposition. The highest sustainability factor (0.66) and carbon yield (424%) were accomplished with the Ni-Co alloy without any significant inactivation for six hours, while the highest carbon efficiency of 36.43 was obtained with the Ni-Co catalyst, which is considered relatively low in comparison with industry standards, indicating a low carbon production process efficiency, possibly due to the relatively high biogas flow rate. The higher activity of the Ni-Co alloy catalyst was associated with the synergistic impact between nickel and cobalt, allowing the catalyst to maintain a high stability throughout the reaction period. Moreover, highly uniform, interwoven carbon bio-nanofilaments with a parallel and fishbone structure were achieved.

1 November 2024 in Results in Engineering
Verified
Journal Article
Open access
NONur Tantiyani Ali Othman
Nur Tantiyani Ali Othman
ZPZulfan Adi Putra
Zulfan Adi Putra
SAShahrul Azman Zainal Abidin
Shahrul Azman Zainal Abidin
FAFadzrul Izwan M Ali
Fadzrul Izwan M Ali

1 January 2011 in Procedia - Social and Behavioral Sciences
Verified
Journal Article
Open access
MMMASTURAH MARKOM
MASTURAH MARKOM
MKMohd Sahaid Khalil
Mohd Sahaid Khalil
RMRahaiza Misnon
Rahaiza Misnon
NONur Tantiyani Ali Othman
Nur Tantiyani Ali Othman
Siti Rozaimah Sheikh AbdullahSiti Rozaimah Sheikh Abdullah
Siti Rozaimah Sheikh Abdullah
AMAbu Bakar Mohamad
Abu Bakar Mohamad
Exposure to real life industries is one of the key elements implicitly emphasized in the Program Outcomes (PO) for students graduated from Chemical and Biochemical Engineering programs. The Department of Chemical and Process Engineering (JKKP) has implemented the Industrial Talk and Industrial Visit activities since 2006, following suggestions from the program external assessors. The activities are important for students to relate their theoretical knowledge to practical aspects of the studied courses, in terms of industrial unit operations, process and design concepts, and impact of its activities on health, safety, environment and society. Recently, the Faculty of Engineering and Built Environment has proposed that students from each academic year should be exposed to industrial talks (twice a year) and industrial visits (once a year). This paper elaborates on the objectives and experiences gained by the JKKP in implementing these activities. The strengths, weaknesses and opportunities for improvement are also identified and discussed. It can be concluded that a good coordination and a proper assessment methods, selection of industrial sites for visit as well as speakers or topics for talks are important for enhancing students’ practical learning

1 January 2011 in Procedia - Social and Behavioral Sciences
Verified
Journal Article
Open access
NONur Tantiyani Ali Othman
Nur Tantiyani Ali Othman
RMRahaiza Misnon
Rahaiza Misnon
Siti Rozaimah Sheikh AbdullahSiti Rozaimah Sheikh Abdullah
Siti Rozaimah Sheikh Abdullah
NKNoorhisham Tan Kofli
Noorhisham Tan Kofli
SKSiti Kartom Kamarudin
Siti Kartom Kamarudin
AMAbu Bakar Mohamad
Abu Bakar Mohamad
Questionnaire of prospective university graduates have been identified as one of the effective methods for the strength and weakness assessment of the program curriculum. It is based on student feedbacks regarding on their performance and satisfaction in Department of Chemical & Process Engineering (JKKP) in order to determine the effectiveness of the Chemical and Biochemical Engineering Program at Faculty of Engineering and Built Environment, UKM. The questionaire include a general information of future graduates, information on program outcomes over 4 years and acquiring skills, career preparation and student-lecturer relationship. The results of the evaluation process and recommendations for improving the curriculum were also studied. The study was conducted over two sessions (semester 2009/2010 and 2010/2011) for two batches of students. Overall, mostly all the prospective graduates are satisfied with the current system of teaching and learning in JKKP as well as also willing to involve into the working environment. Achievement of the 12 program outcomes indicates a satisfactory performance with an average of more than 70% and 57% for respective Chemical and Biochemical Engineering Program. Based on this study, approximately more than 27% graduate in Chemical Engineering believes that the theoritical-practical and technical oriented projects should be adopted, while 19% of Biochemical Engineering graduates thinks that the project design should be separated and should be more focused to the field of biochemical engineering area

1 October 2019 in Jurnal Kejuruteraan
Verified
Journal Article
Closed access
NONur Tantiyani Ali Othman
Nur Tantiyani Ali Othman
MRMuhammad Elmi Fahmi Mohd Razali
Muhammad Elmi Fahmi Mohd Razali

1 June 2013 in Flow Measurement and Instrumentation
Verified
Journal Article
Closed access
NONur Tantiyani Ali Othman
Nur Tantiyani Ali Othman
HOHiromichi Obara
Hiromichi Obara
MTMasahiro Takei
Masahiro Takei