Deformation is a ubiquitous phenomenon in nature. This process usually refers to the change in shape, size, and position of an object in the time and spatial domain under various loads. Under normal circumstances, during engineering construction, technicians are generally required to monitor the safe operation of structural facilities in the transportation field and the health of bridge, because monitoring in the engineering process plays an important role in construction safety. Considering the reliability risk of sensors after a long-time work period, such as signal drift, accurate measurement of strain gauges is inseparable from the value traceability system of high-precision strain gauges. In this study, two vibrating wire strain gauges with the same working principle were measured using the parallel method at similar positions. First, based on the principle of time series, the experiment used high-frequency dynamic acquisition to measure the thermometer strain of two vibrating wire strain gauges. Second, this experiment analyzed the correlation between strain and temperature measured separately. Under the condition of different prestress, this experiment studied the influencing relationship of temperature corresponding variable. In this experiment, the measurement repetitiveness was analyzed using the meteorology knowledge of single sensor data, focused on researching the influence of temperature and prestress effect on sensors by analyzing differences of their measurement results in a specified situation. Then, the reliability and stability of dynamic vibrating wire strain gauge were verified in the experiment. The final conclusion of the experiment is the actual engineering in the later stage. Onsite online meteorology in the application provides support.
It is challenging to find actual standard test roads (ASTRs) to evaluate the measuring performance of the Traffic Speed Deflectometer (TSD), leading to misjudgment of its evaluation results. To address this issue, a method to construct virtual standard test roads (VSTRs) using in-service roads is proposed. Firstly, the principle of TSD based on the Laser-Doppler effect to measure pavement deflection is introduced, and the shortcomings of traditional evaluation methods are reviewed and summarized. Secondly, an adaptive construction method for VSTRs is proposed based on the K-means clustering algorithm. It layers the Falling Weight Deflectometer (FWD) measurements on in-service roads and reconstructs them as virtual roads with stable deflections but different ranges. Thirdly, two new indexes, the coefficient of variation CVk and the influence coefficient of speed ICSk , are proposed to replace the traditional indexes, such as repeatability and correlation coefficient. Finally, the feasibility of evaluating TSD performance based on VSTRs and the new indexes is verified by experiments. Results show that the newly constructed VSTRs solve the problem that the ASTRs are challenging to obtain, reducing the experimental requirements for evaluating TSD, and the new indexes achieve an efficient and scientific evaluation of TSD.
8 October 2021 in Measurement Science and Technology
Aiming at the calibration of in-service strain sensing systems for structural health monitoring (SHM), a technical framework is proposed. A calibration method adapting to complex in-situ conditions is presented which defines the calibration prototype composed of measured variable, excitation source, reference system and sensing system. By analysing the operating procedure of the prototype, two measurement models are deduced for instantaneous and intermediate error analysis respectively. To discover the effects of the ambient temperature on the calibration process, the experiments are conducted using a temperature test chamber, and then the qualitative analysis and quantitative estimation are performed. The results show that: (a) With the variation of temperature, the responses of both resistance strain gauges (RSS) and fiber optic strain sensors (FOS) change significantly; (b) The relative strain deviations between the sensing system (SS) and the reference sensing system (RS) within −10 °C–50 °C fluctuate in a narrow range, for example 0.015–0.023 for RSS and 0.382–0.404 for FOS in this study, respectively; (c) The range of the deviations between SS and RS that is affected by temperature can be estimated with the proposed method, for example, 4.61 μ ϵ for RSS and 18.2 μ ϵ for FOS, respectively, with a confidence level of 95%.
Accurately measuring the incident angle of the laser Doppler vibrometer (LDV) laser beam is crucial for calculating the accurate dynamic response of a target. Nonetheless, conventional measuring methods may encounter limitations due to spatial constraints. To address this issue, a novel high-precision dynamic measuring method is proposed based on the measuring principle of LDV. Furthermore, a compact dynamic measuring device is constructed to facilitate this method. The proposed method involves the simulation of various tangential velocities utilizing a high precision rotating disk system. Subsequently, the laser beam incident angle is computed based on the projection relationship established between the average value of LDV measurements and the simulated velocities. To validate the feasibility of the dynamic measuring method and the correctness of the obtained incident angle, the paper compares this angle with that obtained through a conventional laser beam measuring method and device. This paper analyzes four key factors that may affect the angle measuring results theoretically and experimentally: environmental noise, laser spot position error, roll angle, and pitch angle of the rotating disk. The results indicate that the laser spot position error and the pitch angle of the rotating disk are more influential than the other two factors. Corresponding optimization measures are also proposed to improve the measuring accuracy.
8 August 2025 in Flow Measurement and Instrumentation
This paper mainly conducts research on the electrode distribution of the multi-electrode electromagnetic flow measurement system. Through simulation work, the weight function of the area to which the electrodes on the pipeline cross-section belong with respect to the potential difference is roughly obtained. Moreover, by comparing the simulation data with the actual experimental data, the correctness of the simulation work is verified. Tikhonov regularization is utilized to inversely solve the average velocity of the electrode area, and the TR-CNN algorithm is established to refine the velocity field of the pipeline cross-section in question. It mainly introduces the influence of different electrode placement methods on the potential difference. The results show that it has a relatively small impact on the velocity distribution of the fluid cross-section before flowing through the elbow, and the potential difference is highly sensitive to the velocity in the area where the magnetic induction coil and the electrodes are relatively close. The Pitot tube is used to conduct verification measurements on the fluid velocity field in the pipeline. The results indicate that as the measurement points are farther away from the elbow, the “skewing” phenomenon of the fluid flow velocity gradually weakens. In terms of prediction performance, the mean square error (MSE) of the cross-section error is approximately 0.015, and the mean absolute error (MAE) is about 0.095. These error indicators jointly demonstrate that the system has a relatively high measurement accuracy in practical applications.