Coal dust is a primary threat to underground coal miners. The most common approach to control coal dust is hydraulic methods, such as water spray and coal seam water injection. To improve the dust suppressant efficiency of hydraulic methods, a novel chemical composite dust suppressant, called NCZ, was prepared in this study using calcium chloride (CaCl₂), magnesium chloride (MgCl₂), and nonionic surfactants using a thermal synthesis method. The water-retaining properties of NCZ powder and its solutions were characterized using the water absorption rate (WAR) and evaporation rate (ER), respectively, and the wetting abilities of the NCZ solutions on coal dust were tested using the initial contact angle (ICA) and sink rate (SR). The results indicate that the NCZ solutions have anti-evaporation effects, and the ER of the solution with a 20.0 wt% NCZ is reduced by 11.7% compared with that of clean water. Furthermore, NCZ solutions have remarkable enhancement effects on the wettability of coal dust. The ICA and SR of clean water and the NCZ solution at 20.0 wt% are 141.9° and 0 mg/s, and 29.3° and 1.46 mg/s, respectively. Finally, quantitative relationships between the solution surface tension and the ICA and IR were established using the least squares method. This study provides a new product for dust suppression in underground mines, which is significant for the optimum applied concentration of dust suppressant in mining operations.

Coal dust pollution poses a serious public health threat. This study aimed to investigate the feasibility of creating a coal dust suppressant using molasses, a byproduct of the sugar industry. We studied the effects of a molasses solution of varying concentrations (i.e., ranging from 0% (pure water) to 40%) on the moisture, bonding, and wind erosion properties of coal dust. Overall, the effectiveness of the molasses increased with their concentration, and it manifested itself in the following way: (1) the molasses improved the anti-evaporation ability of wet coal dust. For example, the evaporation mass of the coal dust wetted using a molasses solution decreased by 82.8%; (2) molasses effectively agglutinated coal dust; (3) molasses can effectively decrease the surface tension and increase the viscosity of the wetting solution. The surface tension of the molasses solution reached 41.37 mN/m and the viscosity increased to 6.79 mPa·s; (4) molasses can significantly suppress the wind erosion of deposited coal dust, with its wind erosion mass decreasing 99.1%; finally, (5) the effectiveness of molasses at suppressing coal dust was discussed at a molecular level. This study highlights the feasibility of a low-cost and environment-friendly dust suppressant in coal mines.

Novel DOPO/silicon/CNT nanohybrid flame retardants (FR-CNTs) were synthesized and FR-CNTs were introduced into epoxy resins through thermal curing process. The SEM and TEM results indicate that CNTs distribute uniformly in epoxy resins due to the good dispersion of CNTs in DOPO/silicon/CNT nanohybrid flame retardants. The thermal stability and flame-retardant properties of EP/FR-CNTs composites are improved, which is attributed to the good dispersion of DOPO/silicon/CNT nanohybrid. The cone calorimeter results demonstrate that FR-CNTs can reduce peak heat release and the release of toxic gas effectively compared with EP/CNTs and EP/CNT/FR composites. The char-residue analysis indicates that the improved flame-retardant properties are due to the char-reinforcing effects and the catalyzing charring effect of FR-CNTs, which provides enough time for flame retardants to trap radicals. Generally, the char layers, which act as insulating barrier, can reduce the releasing of flammable gases and protect the underlying epoxy resins from the heat source.

The adsorption, permeability properties, and damage evolution of internal cracks are often not considered in simulation tests for coal and gas outbursts. Therefore, in previous studies of similar materials, the materials used may not be similar in the properties mentioned above. To solve these issues, the adsorption, permeability, mechanical, and acoustic emission (AE) response characteristics of a soft coal solid-gas coupling similar material (SCSCSM) were studied in an orthogonal experiment where gas adsorption, permeability, uniaxial compression, and AE tests were performed. The analysis of the experimental data revealed that the SCSCSM has mechanical, gas adsorption and permeability properties similar to those of soft coal. The mass fraction of humic acid sodium solution (HASS) was the main parameter, affecting physical and mechanical properties. As the mass fraction of HASS increased, the adsorption volume and permeability varied logarithmically and exponentially, respectively. Meanwhile, the failure pattern transitioned from extrusion damage to wedge splitting and brittle shear failure. AE response from the beginning to the peak stress can be divided into a slow increase stage and a rapid increase stage. A damage parameter experienced an initial rise, then a rapid decline, then a quick rise, and finally a slow increase. Through segmentation fitting, expressions of damage evolution mechanisms for each section were obtained. Through the study of SCSCSM's internal gas storage, transport, and mechanical properties, AE response characteristics, and multiscale evaluation of mechanical response, this study has laid a foundation for the subsequent development of solid–gas coupling similar simulation materials and physical simulation experiments of coal and gas outburst for soft coal seams.

A parallel-flow exhaust hood is an effective ventilation device to control dust and toxic pollutants and protect the occupational health of workers, whether it is used alone or combined with a uniform air supply hood in a push–pull ventilation system. Some scholars have studied the outside air flow characteristics of the conventional exhaust hood with non-uniform air speed at the hood face, but the law of velocity variation outside the parallel-flow exhaust hood is not clear at present. Therefore, this paper uses the dimensionless method to study the center-line velocity change regime in a parallel-flow square exhaust hood based on simulation and experimental data. The results show that the dimensionless center-line velocity has a good change law with the characteristic length of exhaust hood in a parallel-flow square exhaust hood, which can eliminate the influence of hood face velocity and the hood size on the velocity change regime; and the experimental data is basically consistent with the calculated data, which shows that the regression equation method is reliable.