An important segment of the future renewable energy economy is the implementation of novel energy generation systems. Such electrochemical systems are solid oxide fuel cells, which have the advantage of direct conversion of the chemical energy stored in the fuel to electrical energy with high efficiency. Improving the performance and lowering the cost of solid oxide fuel cells (SOFCs) are strongly dependent on finding commercially viable methods for nano-functionalization of their electrodes via infiltration. Inkjet printing technology was proven to be a feasible method providing scalability and high-resolution ink delivery. LaxSr1−xCoyFe1−yO3−δ cathodes were modified using inkjet printing for infiltration with two different materials: Gd-doped ceria (CGO) commonly used as ion-conductor and La0.6Sr0.4CoO3–δ (LCO) commonly used as a mixed ionic electronic conductor. As-modified surface structures promoted the extension of the three-phase boundary (TPB) and enhanced the mechanisms of the oxygen reduction reaction. Electrochemical impedance measurements revealed significantly lowered polarization resistances (between 2.7 and 3.7 times) and maximum power output enhancement of 24% for CGO infiltrated electrodes and 40% for LCO infiltrated electrodes.
Single-step inkjet printing infiltration with doped ceria Ce0.9Ye0.1O1.95 (YDC) and cobalt oxide (CoxOy) precursor inks was performed in order to modify the properties of the doped ceria interlayer in commercial (50 × 50 × 0.5 mm3 size) anode-supported SOFCs. The penetration of the inks throughout the La0.8Sr0.2Co0.5Fe0.5O3−δ porous cathode to the Gd0.1Ce0.9O2 (GDC) interlayer was achieved by optimisation of the inks’ rheology jetting parameters. The low-temperature calcination (750 °C) resulted in densification of the Gd-doped ceria porous interlayer as well as decoration of the cathode scaffold with nanoparticles (~20–50 nm in size). The I–V testing in pure hydrogen showed a maximum power density gain of ~20% at 700 °C and ~97% at 800 °C for the infiltrated cells. The latter effect was largely assigned to the improvement in the interfacial Ohmic resistance due to the densification of the interlayer. The EIS study of the polarisation losses of the reference and infiltrated cells revealed a reduction in the activation polarisations losses at 700 °C due to the nano-decoration of the La0.8Sr0.2Co0.5Fe0.5O3−δ scaffold surface. Such was not the case at 800 °C, where the drop in Ohmic losses was dominant. This work demonstrated that single-step inkjet printing infiltration, a non-disruptive, low-cost technique, can produce significant and scalable performance enhancements in commercial anode-supported SOFCs.
Among the next-generation energy storage technologies, lithium-sulfur batteries are considered one of the most appealing solutions owing to their remarkable theoretical capacity. However, to become commercially competitive, there is a strong need to address some issues still characterizing this technology. One of the explored strategies is the optimization of the electrolyte formulation. To this aim, we compared 1,3-dioxolane/1,2-dimethoxyethane-based electrolytes containing two lithium halides, i.e., lithium bromide (LiBr) and lithium iodide (LiI), with lithium bis (trifluoromethane)sulfonylimide (LiTFSI) as a reference electrolyte. The obtained results show how the donicity of the lithium-salt anions might affect the solid electrolyte interphase stability and the lithium sulfide deposition morphology, therefore influencing the electrochemical performance of the cells. Among the tested electrolytes, the sulfur cell containing LiBr salt exhibited the best electrochemical performance maintaining a specific capacity of 900 mAh g−1 at C/4 and a stable trend along cycling at 1C with a specific capacity of about 770 mAh g−1 for 200 cycles.
Lithium–sulfur batteries are considered one of the most appealing technologies for next-generation energy-storage devices. However, the main issues impeding market breakthrough are the insulating property of sulfur and the lithium-polysulfide shuttle effect, which cause premature cell failure. To face this challenge, we employed an easy and sustainable evaporation method enabling the encapsulation of elemental sulfur within carbon nanohorns as hosting material. This synthesis process resulted in a morphology capable of ameliorating the shuttle effect and improving the electrode conductivity. The electrochemical characterization of the sulfur–carbon nanohorns active material revealed a remarkable cycle life of 800 cycles with a stable capacity of 520 mA h/g for the first 400 cycles at C/4, while reaching a value around 300 mAh/g at the 750th cycle. These results suggest sulfur–carbon nanohorn active material as a potential candidate for next-generation battery technology.
The preparation of sulfur-single walled carbon nanohorns active material via a simple and sustainable evaporation method for application as cathode in lithium-sulfur batteries is reported. We show that the synthesis process enables the infiltration of elemental sulfur within the carbon nanohorns thus obtaining a morphology responsible for the ameliorating of the shuttle effect. The sulfur-carbon composite is characterized in terms of structure, morphology, and composition through x-ray diffraction, transmission electron microscopy, and thermogravimetric analyses. From the electrochemical point of view, cyclic voltammetry, rate capability, and galvanostatic cycling tests are performed employing a solution of bis(trifluoromethane)sulfonimide lithium salt and lithium nitrate in a mixture of 1,2-dimethoxyethane and 1,3-dioxolane in order to evaluate the electrode design applicability within lithium-sulfur cells. In this respect, further insights are provided by the estimation of the lithium-ion diffusion coefficient through the Randles-Sevcik equation, and by electrochemical impedance spectroscopy. The obtained results reveal a remarkable cycle life lasting around 800 cycles with a stable capacity of 520 mA h g-1 for the first 400 cycles at C/4, while reaching a value around 300 mA h g-1 at the 750th cycle. These results suggest sulfur-carbon nanohorns active material as a potential candidate for the next-generation battery technology.