Andreas Nylander

Dr. Andreas Nylander

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 September 2024 in PRX Quantum
Verified
Journal Article
Open access
PDF file
SKSandoko Kosen
Sandoko Kosen
HLHang-Xi Li
Hang-Xi Li
MRMarcus Rommel
Marcus Rommel
RRRobert Rehammar
Robert Rehammar
MCMarco Caputo
Marco Caputo
JBJonas Bylander
Jonas Bylander
Quantum processors require a signal-delivery architecture with high addressability (low crosstalk) to ensure high performance already at the scale of dozens of qubits. Signal crosstalk causes inadvertent driving of quantum gates, which will adversely affect quantum gate fidelities in scaled-up devices. Here, we demonstrate packaged flip-chip superconducting quantum processors with signal-crosstalk performance competitive with those reported in other platforms. For capacitively coupled qubit-drive lines, we find on-resonant crosstalk better than −27 dB (average −37 dB). For inductively coupled magnetic-flux-drive lines, we find less than 0.13% direct-current flux crosstalk (average 0.05%). These observed crosstalk levels are adequately small and indicate a decreasing trend with increasing distance, which is promising for further scaling up to larger numbers of qubits. We discuss the implications of our results for the design of a low-crosstalk on-chip signal-delivery architecture, including the influence of a shielding tunnel structure, potential sources of crosstalk, and estimation of crosstalk-induced qubit-gate error in scaled-up quantum processors.

24 April 2017 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
Lin JingLin Jing
Lin Jing
MSMajid Kabiri Samani
Majid Kabiri Samani
BLBo Liu
Bo Liu
HLHongling Li
Hongling Li
RTRoland Yingjie Tay
Roland Yingjie Tay
ATAlfred Tok
Alfred Tok

23 June 2021 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
ANAndreas Nylander
Andreas Nylander
JHJosef Hansson
Josef Hansson
TNTorbjörn Nilsson
Torbjörn Nilsson
LYLilei Ye
Lilei Ye
Yifeng FuYifeng Fu
Yifeng Fu
JLJohan Liu
Johan Liu
Carbon nanotube (CNT) array thermal interface materials (TIMs) are promising candidates for high-performance applications in terms of thermal performance. However, in order to be useful in commercial applications, the reliability of the interfaces is an equally important parameter, which so far has not been thoroughly investigated. In this study, the reliability of CNT array TIMs is investigated through accelerated aging. The roles of CNT array height and substrate configuration are studied for their relative impact on thermal resistance degradation. After aging, the CNT catalyst is analyzed using X-ray photoelectron spectroscopy to evaluate chemical changes. The CNT-catalyst bond appears to degrade during aging but not to the extent that the TIM performance is compromised. On the other hand, coefficient of thermal expansion mismatch between surfaces creates strain that needs to be absorbed, which requires CNT arrays with sufficient height. Transfer and bonding of both CNT roots and tips also create more reliable interfaces. Crucially, we find that the CNT array height of most previously reported CNT array TIMs is not enough to prevent significant reliability problems.

1 June 2024 in APL Quantum
Verified
Journal Article
Open access
PDF file
LCLert Chayanun
Lert Chayanun
JBJanka Biznárová
Janka Biznárová
LZLunjie Zeng
Lunjie Zeng
PMPer Malmberg
Per Malmberg
ANAndreas Nylander
Andreas Nylander
ARAnita Fadavi Roudsari
Anita Fadavi Roudsari
We systematically investigate the influence of the fabrication process on dielectric loss in aluminum-on-silicon superconducting coplanar waveguide resonators with internal quality factors (Qi) of about one million at the single-photon level. These devices are essential components in superconducting quantum processors; they also serve as proxies for understanding the energy loss of superconducting qubits. By systematically varying several fabrication steps, we identify the relative importance of reducing loss at the substrate–metal and substrate–air interfaces. We find that it is essential to clean the silicon substrate in hydrogen fluoride (HF) prior to aluminum deposition. A post-fabrication removal of the oxides on the surface of the silicon substrate and the aluminum film by immersion in HF further improves the Qi. We observe a small, but noticeable, adverse effect on the loss by omitting either standard cleaning (SC1), pre-deposition heating of the substrate to 300 °C, or in situ post-deposition oxidation of the film’s top surface. We find no improvement due to excessive pumping meant to reach a background pressure below 6 × 10−8 mbar. We correlate the measured loss with microscopic properties of the substrate–metal interface through characterization with x-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectrometry, transmission electron microscopy, energy-dispersive x-ray spectroscopy, and atomic force microscopy.

1 July 2025 in New Journal of Physics
Verified
Journal Article
Open access
CKChristian Križan
Christian Križan
JBJanka Biznárová
Janka Biznárová
LCLiangyu Chen
Liangyu Chen
EHEmil Hogedal
Emil Hogedal
AOAmr Osman
Amr Osman
JBJonas Bylander
Jonas Bylander
It is advantageous for any quantum processor to support different classes of two-qubit quantum logic gates when compiling quantum circuits, a property that is typically not present in existing platforms. In particular, access to a gate set that includes support for the CZ-, iSWAP-, and SWAP-type families of gates renders conversions between these gate families unnecessary during compilation, as any two-qubit Clifford gate can be executed using at most one two-qubit gate from this set, plus additional single-qubit gates. We experimentally demonstrate that a SWAP gate can be decomposed into one iSWAP gate followed by one CZ gate, affirming a more efficient compilation strategy over the conventional approach that relies on three iSWAP or three CZ gates to replace a SWAP gate. Our implementation makes use of a superconducting quantum processor design based on fixed-frequency transmon qubits coupled together by a parametrically modulated tunable transmon coupler, extending this platform’s native gate set so that any two-qubit Clifford unitary matrix can be realized using no more than two two-qubit gates and single-qubit gates.

7 August 2023 in IEEE Transactions on Quantum Engineering
Verified
Journal Article
Open access
HLHang-Xi Li
Hang-Xi Li
DSDaryoush Shiri
Daryoush Shiri
SKSandoko Kosen
Sandoko Kosen
MRMarcus Rommel
Marcus Rommel
LCLert Chayanun
Lert Chayanun
JBJonas Bylander
Jonas Bylander
In superconducting quantum processors, the predictability of device parameters is of increasing importance as many labs scale up their systems to larger sizes in a 3D-integrated architecture. In particular, the properties of superconducting resonators must be controlled well to ensure high-fidelity multiplexed readout of qubits. Here we present a method, based on conformal mapping techniques, to predict a resonator's parameters directly from its 2D cross-section, without computationally heavy and time-consuming 3D simulation. We demonstrate the method's validity by comparing the calculated resonator frequency and coupling quality factor with those obtained through 3D finite-element-method simulation and by measurement of 15 resonators in a flip-chip-integrated architecture. We achieve a discrepancy of less than 2% between designed and measured frequencies, for 6-GHz resonators. We also propose a design method that reduces the sensitivity of the resonant frequency to variations in the inter-chip spacing.