We present a comprehensive study of internal quality factors in superconducting stub-geometry three-dimensional cavities made of aluminum. We use wet etching, annealing, and electrochemical polishing to improve the as machined quality factor. We find that the dominant loss channel is split between the two-level system loss and an unknown source with a 40:60 proportion. A total of 17 cavities of different purity, resonance frequency, and size were studied. Our treatment results in reproducible cavities, with 10 of them showing internal quality factors above 80 × 106 at a power corresponding to an average of a single photon in the cavity. The best cavity has an internal quality factor of 115 × 106 at a single photon level.
We demonstrate aluminum-on-silicon planar transmon qubits with time-averaged T1 energy relaxation times of up to 270 μs, corresponding to Q = 5 million, and a highest observed value of 501 μs. Through materials analysis techniques and numerical simulations we investigate the dominant source of energy loss, and devise and demonstrate a strategy toward its mitigation. Growing aluminum films thicker than 300 nm reduces the presence of oxide, a known host of defects, near the substrate-metal interface, as confirmed by time-of-flight secondary ion mass spectrometry. A loss analysis of coplanar waveguide resonators shows that this results in a reduction of dielectric loss due to two-level system defects. The correlation between the enhanced performance of our devices and the film thickness is due to the aluminum growth in columnar structures of parallel grain boundaries: transmission electron microscopy shows larger grains in the thicker film, and consequently fewer grain boundaries containing oxide near the substrate-metal interface.
26 September 2022 in IEEE Transactions on Quantum Engineering
We fabricate and characterize superconducting through-silicon vias and electrodes suitable for superconducting quantum processors. We measure internal quality factors of a million for test resonators excited at single-photon levels, on chips with superconducting vias used to stitch ground planes on the front and back sides of the chips. This resonator performance is on par with the state of the art for silicon-based planar solutions, despite the presence of vias. Via stitching of ground planes is an important enabling technology for increasing the physical size of quantum processor chips, and is a first step toward more complex quantum devices with three-dimensional integration.
We systematically investigate the influence of the fabrication process on dielectric loss in aluminum-on-silicon superconducting coplanar waveguide resonators with internal quality factors (Qi) of about one million at the single-photon level. These devices are essential components in superconducting quantum processors; they also serve as proxies for understanding the energy loss of superconducting qubits. By systematically varying several fabrication steps, we identify the relative importance of reducing loss at the substrate–metal and substrate–air interfaces. We find that it is essential to clean the silicon substrate in hydrogen fluoride (HF) prior to aluminum deposition. A post-fabrication removal of the oxides on the surface of the silicon substrate and the aluminum film by immersion in HF further improves the Qi. We observe a small, but noticeable, adverse effect on the loss by omitting either standard cleaning (SC1), pre-deposition heating of the substrate to 300 °C, or in situ post-deposition oxidation of the film’s top surface. We find no improvement due to excessive pumping meant to reach a background pressure below 6 × 10−8 mbar. We correlate the measured loss with microscopic properties of the substrate–metal interface through characterization with x-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectrometry, transmission electron microscopy, energy-dispersive x-ray spectroscopy, and atomic force microscopy.
It is advantageous for any quantum processor to support different classes of two-qubit quantum logic gates when compiling quantum circuits, a property that is typically not present in existing platforms. In particular, access to a gate set that includes support for the CZ-, iSWAP-, and SWAP-type families of gates renders conversions between these gate families unnecessary during compilation, as any two-qubit Clifford gate can be executed using at most one two-qubit gate from this set, plus additional single-qubit gates. We experimentally demonstrate that a SWAP gate can be decomposed into one iSWAP gate followed by one CZ gate, affirming a more efficient compilation strategy over the conventional approach that relies on three iSWAP or three CZ gates to replace a SWAP gate. Our implementation makes use of a superconducting quantum processor design based on fixed-frequency transmon qubits coupled together by a parametrically modulated tunable transmon coupler, extending this platform’s native gate set so that any two-qubit Clifford unitary matrix can be realized using no more than two two-qubit gates and single-qubit gates.
Two-level system (TLS) loss typically limits the coherence of superconducting quantum circuits. The loss induced by TLS defects is nonlinear, resulting in quality factors with a strong dependence on the circulating microwave power. We observe frequency mixing due to this nonlinearity by applying a two-tone drive to a coplanar waveguide resonator and measuring the intermodulation products using a multifrequency lock-in technique. This intermodulation spectroscopy method provides an efficient approach to characterizing TLS loss in superconducting circuits. Using harmonic balance reconstruction, we recover the nonlinear parameters of the device-TLS interaction, which are in good agreement with the standard tunneling model for TLSs. Published by the American Physical Society 2024