Maximum power point tracking (MPPT) techniques are used in photovoltaic (PV) systems to maximize the PV array output power by tracking continuously the maximum power point (MPP) which depends on panels temperature and on irradiance conditions. The issue of MPPT has been addressed in different ways in the literature but, especially for low-cost implementations, the perturb and observe (P&O) maximum power point tracking algorithm is the most commonly used method due to its ease of implementation. A drawback of P&O is that, at steady state, the operating point oscillates around the MPP giving rise to the waste of some amount of available energy; moreover, it is well known that the P&O algorithm can be confused during those time intervals characterized by rapidly changing atmospheric conditions. In this paper it is shown that, in order to limit the negative effects associated to the above drawbacks, the P&O MPPT parameters must be customized to the dynamic behavior of the specific converter adopted. A theoretical analysis allowing the optimal choice of such parameters is also carried out. Results of experimental measurements are in agreement with the predictions of theoretical analysis.

Power processing systems will be a key factor of future photovoltaic (PV) applications. They will play a central role in transferring, to the load and/or to the grid, the electric power produced by the high-efficiency PV cells of the next generation. In order to come up the expectations related to the use of solar energy for producing electrical energy, such systems must ensure high efficiency, modularity, and, particularly, high reliability. The goal of this paper is to provide an overview of the open problems related to PV power processing systems and to focus the attention of researchers and industries on present and future challenges in this field.

One of the major drawbacks of photovoltaic (PV) systems is represented by the effect of module mismatching and of partial shading of the PV field. Distributed maximum power point tracking (DMPPT) is a very promising technique that allows the increase of efficiency and reliability of such systems. Modeling and designing a PV system with DMPPT is remarkably more complex than implementing a standard MPPT technique. In this paper, a DMPPT system for PV arrays is proposed and analyzed. A dc and small-signal ac model is derived to analyze steady-state behavior, as well as dynamics and stability, of the whole system. Finally, simulation results are reported and discussed.

In double-stage grid-connected photovoltaic (PV) inverters, the dynamic interactions among the DC/DC and DC/AC stages and the maximum power point tracking (MPPT) controller may reduce the system performances. In this paper, the detrimental effects, particularly in terms of system efficiency and MPPT performances, of the oscillations of the PV array voltage, taking place at the second harmonic of the grid frequency are evidenced. The use of a proper compensation network acting on the error signal between a reference signal provided by the MPPT controller and a signal that is proportional to the PV array voltage is proposed. The guidelines for the proper joint design of the compensation network (which is able to cancel out the PV voltage oscillations) and of the main MPPT parameters are provided in this paper. Simulation results and experimental measurements confirm the effectiveness of the proposed approach.

The main design objective of photovoltaic (PV) systems has been, for a long time, to extract the maximum power from the PV array and inject it into the ac grid. Therefore, the maximum power point tracking (MPPT) of a uniformly irradiated PV array and the maximization of the conversion efficiency have been the main design issues. However, when the PV plant is connected to the grid, special attention has to be paid to the reliability of the system, the power quality, and the implementation of protection and grid synchronization functions. Modern power plants are required to maximize their energy production, requiring suitable control strategies to solve the problems related to the partial shading phenomena and different orientation of the PV modules toward the sun. Moreover, the new policy concerning the injection of reactive power into the grid makes the development of suitable topologies and control algorithms mandatory. A general view of actual solutions for applications of the PV energy systems is presented. This article covers several important issues, including the most reliable models used for simulation, which are useful in the design of control systems, and the MPPT function, particularly in distributed applications. The main topologies used in the PV power processing system and, finally, grid connection aspects are discussed, with emphasis on synchronization, protections, and integration.

The perturb and observe (P&O) best operation conditions are investigated in order to identify the edge efficiency performances of this most popular maximum power point tracking (MPPT) technique for photovoltaic (PV) applications. It is shown that P&O may guarantee top-level efficiency, provided that a proper predictive (by means of a parabolic interpolation of the last three operating points) and adaptive (based on the measure of the actual power) hill climbing strategy is adopted. The approach proposed is aimed at realizing, in addition to absolute best tracking performances, high robustness and promptness both in sunny and cloudy weather conditions. The power gain with respect to standard P&O technique is proved by means of simulation results and experimental measurements performed on a low power system. Besides the performance improvements, it is shown that the proposed approach allows possible reduction of hardware costs of analog-to-digital (A/D) converters used in the MPPT control circuitry.