Jason Ostanek

Dr. Jason Ostanek

School of Engineering Technology, Purdue University, 401 N. Grant St. West Lafayette, IN 47907, USA
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2024 in Applied Energy
Verified
Journal Article
Closed access
DADiego Aguilar
Diego Aguilar
JQJhon J. Quinones
Jhon J. Quinones
LPLuis R. Pineda
Luis R. Pineda
Jason OstanekJason Ostanek
Jason Ostanek
LCLuciano Castillo
Luciano Castillo

1 September 2023 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
Jason OstanekJason Ostanek
Jason Ostanek
MPMohammad Parhizi
Mohammad Parhizi
WLWeisi Li
Weisi Li
GKGozdem Kilaz
Gozdem Kilaz
KCK. R. Crompton
K. R. Crompton
A high-resolution, 3D, computational fluid dynamics (CFD) model was developed and implemented for simulating the heat and gas generation during thermal runaway failure of an 18650 Li-ion battery cell. The model accounts for volumetric gas generation within the active material of the cell and for gas flow through the jellyroll, into the headspace regions, through the safety vent, and out into the surrounding air space. The simulation captures the key features of the oven test, including: self-heating from decomposition reactions, initial venting (i.e. blowdown), temperature decrease due to evaporative cooling, thermal runaway, a second venting event associated with thermal runaway, and cooldown. The highly detailed geometric model of the safety vent allowed for new insight into the physics of venting during thermal runaway. Secondary flows, including ring vortices, counter-rotating vortex pairs, and corner vortices, were found to increase the rate of mixing of the vented gases with the surrounding air. The simulation was compared to previously reported experimental results and found to have good qualitative agreement of jet flow direction. The present thermal abuse model forms the basis for future studies to consider the role of gas impingement heat transfer and gas combustion in full battery pack propagating failures.

16 May 2022 in Journal of Power Sources
Verified
Journal Article
Closed access
MPMohammad Parhizi
Mohammad Parhizi
AJAnkur Jain
Ankur Jain
GKGozdem Kilaz
Gozdem Kilaz
Jason OstanekJason Ostanek
Jason Ostanek

7 December 2021 in Frontiers in Energy Research
Verified
Journal Article
Open access
WLWeisi Li
Weisi Li
VQVanessa León Quiroga
Vanessa León Quiroga
KCK. R. Crompton
K. R. Crompton
Jason OstanekJason Ostanek
Jason Ostanek
High temperature gases released through the safety vent of a lithium-ion cell during a thermal runaway event contain flammable components that, if ignited, can increase the risk of thermal runaway propagation to other cells in a multi-cell pack configuration. Computational fluid dynamics (CFD) simulations of flow through detailed geometric models of four vent-activated commercial 18650 lithium-ion cell caps were conducted using two turbulence modeling approaches: Reynolds-averaged Navier-Stokes (RANS) and scale-resolving simulations (SRS). The RANS method was compared with independent experiments of discharge coefficient through the cap across a range of pressure ratios and then used to investigate the ensemble-averaged flow field for the four caps. At high pressure ratios, choked flow occurs either at the current collector plate when flow through the current collector plate is more restrictive or the positive terminal vent holes when flow through the current collector plate is less restrictive. Turbulent mixing occurred within the vent cap assembly, in the jets emerging from the vent holes, and in recirculating zones directly above the vent cap assembly. The global maximum turbulent viscosity ratio (μT/μ) of the MTI, LG MJ1, K2, and LG M36 caps at pressure ratio ofP1/P2= 7 were 4,575, 3,360, 3,855, and 2,993, respectively. SRS and RANS simulations showed that both velocity magnitude and fluctuating velocity magnitude were lower for vent holes which are obstructed by the burst disk. SRS showed high levels of fluctuating velocity in the jets, up to 48.5% of the global maximum velocity. The present CFD models and the resulting insights provide the groundwork for future studies to investigate how jet structure and turbulence levels influence combustion and heat transfer in propagating thermal runaway scenarios.

13 May 2019 in Drying Technology
Verified
Journal Article
Closed access
Jason OstanekJason Ostanek
Jason Ostanek
KIKlein Ileleji
Klein Ileleji
A conjugate heat and mass transfer model was implemented into a commercial CFD code to analyze the convective drying of corn. The Navier–Stokes equations for drying air flow were coupled to diffusion equations for heat and moisture transport in a corn kernel during drying. Model formulation and implementation in the commercial software is discussed. Validation simulations were conducted to compare numerical results to experimental, thin-layer drying data. The model was then used to analyze drying performance for a compact, crossflow dehydrator. At low inlet air temperatures, the drying rate in the compact dehydrator matched the thin-layer drying rate. At higher temperatures, heat losses through the external walls resulted in temperature and moisture variations across the dehydrator.

1 September 2024 in The Electrochemical Society Interface
Verified
Journal Article
Closed access
PDF file
PCPaul T Coman
Paul T Coman
AWAndrew Weng
Andrew Weng
Jason OstanekJason Ostanek
Jason Ostanek
EDEric C. Darcy
Eric C. Darcy
DFDonal Finegan
Donal Finegan
RWRalph E. Edward White
Ralph E. Edward White
This article discusses the dual challenges of modeling and predicting thermal runaway (TR) in li-ion batteries. It explores the current challenges of TR modeling, the methods for progressing from single cells to battery packs, and future directions involving the use of probabilistic methods and ML/AI to tackle this multifaceted issue. Accurate prediction of TR events remains a major challenge, especially because of the cell-to-cell variability, but also due to parametrization, which requires complex experimentation or exhaustive experimental data for training data-driven ML models. Continued research and innovation in modeling and predictive techniques are essential for ensuring safer and more reliable battery systems.