Water transfer through porous textiles consists of two sequential processes: synchronous wicking–evaporating and evaporating alone. In this work we set out to identify the main structural parameters affecting the water transfer process of cotton fabrics. Eight woven fabrics with different floats were produced. The fabrics were evaluated on a specially designed instrument capable of measuring the water loss through a vertical wicking process. Each test took 120 min, and two phases were defined: Phase I for the first 10 min and Phase II for the last 110 min according to wicking behavior transition. Principal components and multivariate statistical methods were utilized to analyze the data collected. The results showed that Phase I dominated the whole wicking–evaporating process, and the moisture transfer speed in this phase varied with fabric structure, whereas the moisture transfer speeds in Phase II were similar and constant regardless of fabric structure. In addition, fabric with more floats has high water transfer speed in Phase I due to its loosened structure with more macropores.
The repair and reconstruction of tracheal defects is a challenging clinical problem. Due to the wide choice of materials and structures, weaving technology has shown unique advantages in simulating the multilayer structure of the trachea and providing reliable performance. Currently, most woven stent-based stents focus only on the effect of materials on stent performance while ignoring the direct effect of woven process parameters on stent performance, and the advantages of weaving technology in tissue regeneration have not been fully exploited. Therefore, this review will introduce the effects of stent materials and fabric construction on the performance of tracheal stents, focusing on the effects of weaving process parameters on stent performance. We will summarize the problems faced by woven stents and possible directions of development in the hope of broadening the technical field of artificial trachea preparation.
26 December 2018 in The Journal of the Textile Institute
The tapered circular tubular (TCT) woven fabric has been applied successfully as the components in vascular prostheses. The application of tapered tubular woven fabric based on the existing weaving technology requires the densification of a large end to ensure porosity uniformity through the tapered tubule. Although the previously proposed equal-cover-factor (ECF) design technique overcame some disadvantages of the conventional densification methods, such as the protruding portions of the dropped yarns as well as the change of both fabric porosity and tensile strength, the off-loom weft density significantly deviates from the on-loom value. On the basis of ECF design technique and the basic shed geometry, this study rebuilt the relative motion relationship among the front rest, the cloth fell, the back rest, and the take-up length, and modified the weft density on loom to achieve continuous weaving process of TCT fabric as well as the uniform porosity. And then, a computerized weaving procedure based on the rebuilt relationship was developed to automatically weave TCT fabric with different weaves on the customized shuttle loom. As a result, the uniform porosity of those samples validated the proposed weaving techniques.
In this article, the harness cords were manufactured by braiding, coating and heat setting at the temperatures of 130 and 195℃, respectively. The film formers used in coating process were poly(butyl acrylate), copolymer size and partial alcoholysis polyvinyl alcohol. The pure film formers' spectra were obtained using in-situ infrared test method on a spectrometer. The scanning electron microscope, bending tester and wearing test device were used to measure the morphology, bending rigidity and wearability of harness cords, respectively. The results showed that the temperature of heat setting changed the molecular structure of coatings, and different influences of temperature on the bending rigidity and wearability of coated harness cords were observed. When the heat setting temperature rose from 130 to 195℃, the bending rigidity of poly(butyl acrylate)-coated harness cord almost kept constant. However, the bending rigidity of copolymer size and polyvinyl alcohol-coated harness cords increased by 33.1% and decreased by 47.4%, respectively. The poly(butyl acrylate) coating presented the best adhesivity to hydrophobic polyester harness cord, and the coated harness cord showed the best uniformity and flexibility as well as higher wearability. After heat setting at 195℃, the wearability of harness cords coated with poly(butyl acrylate), copolymer size and polyvinyl alcohol was increased by 380, 120 and 585%, respectively, when compared with the uncoated one.