In this study, fly ash (FA) coated with ZIF-8 (ZIF-8/FA) nanocomposite was first synthesized by taking 2-methylimidazole and zinc nitrate hexahydrate as reactants and then used as an adsorbent for adsorption of copper, zinc, and nickel ions from aqueous solution. The characteristic of FA and ZIF-8/FA samples were analyzed based on the data from scanning electronic microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, grain size analyzer and N2 adsorption-desorption isotherm. The results showed that ZIF-8 deposited on the FA evenly. The average crystallite size of ZIF-8 on the surface of FA is 15.85 nm. The specific surface area of FA was increased from 1.8 to 249.5 m2/g. The adsorption efficiency of the ZIF-8/FA nanocomposite for the removal of heavy metal ions from aqueous solution was optimized in terms of different parameters such as pH, adsorbent dosage, and contact time. It was shown that the saturated adsorption amounts of the obtained composite for adsorption of Cu2+, Zn2+, and Ni2+ are 335, 197, and 93 mg·g−1. ZIF-8/FA had better stability and more mesoporous volume than that of ZIF-8 and exhibited higher rate for adsorption of heavy metal ions from aqueous solution than FA and ZIF-8, suggesting an adsorption synergy between ZIF-8 and FA. The adsorption mechanism of heavy metal ions by ZIF-8/FA includes surface adsorption, pore adsorption, and ion exchange. The obtained ZIF-8/FA nanocomposite can solve the encountered problems of FA for low adsorption and the difficult recycling of ZIF-8 for their small size, high cost, and poor stability.
The bubble size distribution, location distribution, and gas holdup in a gas–liquid–solid flow three-phase stirred tank were numerically simulated by the Eulerian–Eulerian method and the population balance model (PBM). The Euler–Euler method combined with the PBM model included the influence of bubble aggregation and fragmentation on the interfacial force, which can better predict the bubble size distribution and phase holdups. The simulation results show that there are some differences in the fluid morphology and gas dispersion characteristics in the stirred tank under different rotating speeds. With the increase of rotating speed, the content of small-diameter bubbles increases obviously, and they are mainly concentrated in areas with higher speeds. The higher the rotational speed, the more the bubbles with small diameters, but the content of bubbles with large diameters is less affected by the rotational speed. Small-size bubbles mainly exist in the region of high fluid velocity, while large-size bubbles mainly exist in the region of low hydrostatic pressure. Compared with the change of the bubble content at different speeds, the content of bubbles with diameters of 0.50–1.90 mm is largest at 2000 rpm, while the content of bubbles with diameters of 2.65–10.09 mm is largest at 1500 rpm. The simulation work has certain guiding significance for the research and development of the forced mineralization device and the understanding of the dispersion characteristics of bubbles in the stirred tank.
13 July 2022 in International Journal of Minerals, Metallurgy and Materials
In this study, the effect of hydrodynamic cavitation (HC) on the conditioning stage (HCCS), separation stage (HCSS), and whole stage (HCWS) of coal flotation was investigated by flotation tests, laser granulometry, and contact angle measurements. The flotation results indicate that compared to conventional flotation, all HC-assisted flotation methods can improve concentrate combustible recovery and flotation constant rate. HCCS and HCSS show similar levels of improvement, while HCWS has a better flotation efficiency. The screening tests demonstrate that HC has the advantage of being able to liberate coarse coal particles (+0.25 mm) prior to being combined with gangues. On one hand, HC promotes the dispersion of both particles and agents, while longer cavitation time in HCCS does not lead to better flotation performance. On the other hand, enhancement of the adsorption of the collector on the surface of coal particles in HCCS is confirmed by flotation concentrate contact angle tests. However, HCSS leads to a decrease in concentrate hydrophobicity, compared to conventional flotation. The micro-nanobubbles generated by HC play an important role in improving flotation performance. HCWS offers the advantages of both HCCS and HCSS, and the cooperated mechanism of different HC modes enhances the recovery of coal particles in flotation.
17 January 2022 in Particulate Science and Technology
The computational fluid dynamics-discrete element coupling method is used to simulate the suspension behavior of solid particles in a stirred tank, and the motion trajectories and collision motions of millions of particles are analyzed. These particles have complex interactions with the liquid and the rotating impeller. In this article, we introduce a slip grid method, which is an important method to realize the CFD-DEM coupling. We discuss the influence of liquid flow on the trajectory of solid particles, and analyze the relationship between the eight physical properties of solid particles. It can be concluded that the CFD-DEM coupled approach provides a theoretical way to understand the physics of particle movement in micro- to macro-scales in the solid suspension of a stirred tank.
A magnesium hydroxide (MH)-modified calcined fly ash (CFA) nanocomposite (CFAMH) with core-shell structure was obtained with a heterogeneous nucleation method, and its application for removal of copper, zinc and nickel ions from aqueous acidic solution was studied. The microstructure and surface properties of CFA, CFAMH and MH powders were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller specific surface area (BET), X-ray diffraction (XRD) and Fourier translation infrared spectroscopy (FTIR), respectively. The preparation mechanism of CFAMH was discussed based on zeta potential and FTIR data. The results showed that nano-flake MH with thickness 13.4 nm was well coated on the surface of CFA. The specific surface area was increased from 2.5 to 31.0 m2/g. Si-O-Mg-OH bonds formed from the condensation of Si-OH and Mg-OH. The removal efficiency of heavy metals on CFAMH nanocomposite is higher than that of CFA and MH and follows an order of Cu2+ > Zn2+ > Ni2+. Solubility product constant (Ksp) is an important constant for the removal order of heavy metals on FA, CFAMH and MH. CFAMH nanocomposite can be a cheap material for removing heavy metal ions from acidic wastewater.