The reduction of CO₂ emissions has become a global concern. In this regard, the EU intends to cut CO₂ emissions by 55% by 2030 compared to those of 1990. The utilization of shallow geothermal energy (SGE) in EU countries is considered the most effective measure for decarbonizing heating and cooling. SGE systems utilize heat energy collected from the earth’s crust to provide secure, clean, and ubiquitous energy. This paper provides a literature review on the use of SGE for heating and cooling purposes. The latest advances in materials, new innovative structures, and techno-economic optimization approaches have been discussed in detail. Shallow geothermal energy’s potential is first introduced, and the innovative borehole structures to improve performance and reduce installation cost is outlined. This is followed by an extensive survey of different types of conventional and thermally enhanced collectors and grouts. Attention is mainly given to the techno-economic analysis and optimization approaches. In published case studies, the least economic break-even point against fossil fuel-based heating systems occurs within 2.5 to 17 years, depending on the local geological conditions, installation efficiency, energy prices, and subsidy. Ground source heat pumps’ cost-effectiveness could be improved through market maturity, increased efficiency, cheap electricity, and good subsidy programs.

Textile based sensors were developed and used for remote monitoring of breathing. The breathing is simulated by using a new cyclic tester device. In the simulated a cyclic force is applied along the length of the textile sensor. However due to the morphology of human body, in real situation the sensor is not only under stretching but also under a certain degree of bending. A prototype garment with the sensor situated on the chest area was made. The prototype was worn by 10 persons, and breathing was recorded as the persons were sitting still, walking and jogging. Deep breathing in the supine position and breathing with a method called athletic breathing were used to evaluate the sensor. A testing circuit and a Labview program were made for preliminary test. The sensor is wearable, washable and comfortable. Sensor construction is totally 'disappearing' and visualize as printed pattern onto the surface of garment.

An experimental study of high-density polyethylene (HDPE) composites filled with talc (0–15 wt.%) was carried out to investigate the rheological properties. The apparent melt viscosity, melt density, and die-swell ratio (B) of the composites were measured at constant shear stress and constant shear rate by using a melt flow indexer and capillary rheometer. The experimental conditions were set to a temperature range from 190 to 220 °C for both apparatuses whereas a load range from 5 to 12.16 kg was selected for melt flow indexer and shear rate range from 1 to 10000 s⁻¹ for capillary rheometer. The initial study showed that the talc particulates did not influence the melt viscosity compared with the neat HDPE but decreased the elasticity of the polymer system. The HDPE/talc systems obeyed power-law model in shear stress–shear rate variations and were shear thinning, meanwhile, the die-swell increased with an increased wall shear rate and shear stress. The melt density of the composites increased linearly with an increase of the filler weight fraction and decreased with the increase of the testing temperature. The talc-HDPE composites showed compressible in the molten state.

In this study, a commercial grade of talc is used as filler in a bimodal high‐density polyethylene (HDPE) used for the pressure pipe application. The composites are characterized by thermogravimetric analysis (TGA), differential scanning calorimetry, dynamic mechanical thermal analysis, and tensile testing. The results illustrate that the presence of talc has a considerable effect on the material properties and the pipe life‐length. It is presented that the thermal stability measured by TGA is enhanced, while the oxidation induction time decreases in cooperation of the talc. The nucleation behavior of talc particles during crystallization has no obvious effect on melting temperature; however, an increase in crystallization temperature is evidenced. Storage modulus as recorded from the dynamic mechanical analysis is also increased in all composites, furthermore, the temperature of the α relaxation is shifted toward higher temperature and finally the strain hardening modulus for the HDPE/talc composites is assessed and compared to the neat HDPE as a measure of environmental stress crack resistance.