When an input terminal is connected to a solar panel with a low voltage level and large power range fluctuation, a Boost type CLLC converter controlled by fixed frequency pulse width modulation (PWM) reduces the utilization of PV electric energy, and the synchronous drive of the secondary side and primary side ensures that the converter operates with low efficiency when the duty cycle is shifted by 0.5. To maximize the utilization of photovoltaic (PV) energy in a PV power generation system and improve the conversion efficiency, this paper studies a Boost CLLC converter with high gain and soft switching controlled by PWM-pulse frequency modulation (PFM) hybrid modulation for PV power generation. By controlling the duty cycle and switching frequency of the primary MOSFETs, the converter can stabilize the output voltage while tracking the PV maximum power point. Under such a hybrid control, the resonant gain of the converter is greater than 1, the voltage gain is large, one of the MOSFETs at the primary side is in a zero-voltage-switching-open (ZVS-ON) state, two diodes are used to realize zero-current-switching (ZCS) soft switching on the secondary side, and the efficiency of the converter is high. In addition, this paper studies the phenomenon of backflow power in the resonant circuit and the influence of a change in the switching frequency on the magnitude of the backflow power. Finally, a 500W experimental prototype was constructed to verify the accuracy of the theoretical analysis and the feasibility of the control method.
In DC microgrids, distributed energy storage plays a key role in stabilizing the DC bus voltage. The bidirectional DC/DC converter in the distributed energy storage system should be designed according to the voltage level and electromagnetic isolation requirements, and multiple energy storage units should be coordinated for load current distribution according to the state of charge (SOC). This paper proposes a SOC power index droop control strategy by communication lines to coordinate the fast and high-precision distribution of load current among multiple energy storage units, and the SOC between energy storage units quickly converges to a consistent state. Considering that communication lines are susceptible to interference, this paper further proposes an improved SOC power index droop control to overcome the effects of communication line failures. Considering the high cost of the energy storage unit, it should be connected to the DC microgrid in layers to achieve a reasonable allocation of resources in practical applications. In order to provide high-quality power to a large power grid, the quantification standards of the DC bus fluctuation range and the working range of each converter are further discussed to maximize the stability of the DC bus voltage and grid-connected power fluctuation.
In order to accurately simulate vehicles' running states of lane changing and more effectively reflect its characteristics, based on the driving experience, this paper introduced three changing rules and their corresponding lane changing benefits and safety factors, and summarized the lateral and longitudinal motion of vehicles as the interaction result between lane changing benefits and safety factors in the lane changing process. Taking the basic idea of artificial potential field for reference, the lane changing benefits and safety factors are abstracted respectively as the attractive and repulsive force perceived by drivers, and then the lane changing model corresponding to each lane changing rule was established after analyzing. Finally, the measured data were used to calibrate and test the parameters of lane changing model of different rules. The results showed that the testing errors of the models are within a reasonable range, and the changing trend of lane changing of different rules can be well fitted.
Flying-capacitor multiplexed modulation technology is suitable for bipolar DC microgrids with higher voltage levels and higher current levels. The module combination and corresponding modulation method can be flexibly selected according to the voltage level and capacity level. This paper proposes a bipolar bidirectional DC/DC converter and its interleaved-complementary modulation strategy that is suitable for bipolar DC microgrids. The converter consists of two flying-capacitor three-level bidirectional DC/DC converters that are interleaved in parallel 90°, and then cascaded with another module to form a symmetrical structure of the upper and lower arms; the complementary modulation of the upper and lower half bridges constitutes an interleaved complementary multilevel bidirectional DC/DC converter. If the bidirectional converter needs to provide a stronger overcurrent capability, more bridge arms can be interleaved in parallel. Once n bridge arms are connected in parallel, the bridge arms should be interleaved 180°/n in parallel. In bipolar DC microgrids, the upper and lower arms should be complementarily modulated, and the input and output are isolated by the inductance. To solve the current difference, caused by the inconsistent parasitic, the voltage-current double closed-loop-control is used, and the dynamic response is faster during bidirectional operation. This paper proposes theoretical analysis and experiments that verify bipolar bidirectional DC/DC converter for high-power energy storage.
1 July 2019 in IOP Conference Series: Earth and Environmental Science
There are two main testing methods for the key parameters of the transformer on-load tap changer. One is the DC test method and the other is the AC test method. Based on the AC test method for on-load tap changer key parameters, a new test scheme was proposed. The on-load tap changer switching operation of the transformer can be simulated by establishing a model. The waveforms of the transitional AC current and the testing AC voltage are stored and preprocessed. Then the transitional AC current is equivalent to DC components through the Park transformation. By using the off-line identification algorithm, the transient stage of the transformer on-load tap changers can be determined and the transition resistance value can be accurately calculated.
In this article, a topology based on the single-phase full-bridge is proposed to decouple control of phase current in current source grid-connected inverters. The DC side of this current source inverter topology can operate with a common DC bus or independently, and the AC side can be independently integrated into the three-phase grid or operate in parallel. This topology needs only a simple control logic and phase information to achieve 3-phase current decoupling control, which can accommodate a wide range of voltage fluctuations. Then, dual-carrier driving and hybrid damping correction strategies are designed to achieve flexible combinatorial operation and eliminate the common-mode voltage. Meanwhile, the method is simple and easy to implement in practice. The effectiveness of the proposed algorithm is validated with experiments.