5 May 2021 in IEEE Transactions on Industrial Electronics
LLC half-bridge converters have been extensively studied in low power industrial applications. However, the phase shift angle between the voltage and current of the LLC resonant network makes the converter have power circulation, that is, backflow power. The increase of the backflow power will increase the converter conduction loss, which restricts the improvement of the converter efficiency. The existing literature often improves the backflow power from the control aspect, which greatly increases the control complexity. To solve this problem, this article proposes an LLC half-bridge resonant converter analysis method that takes the backflow power into account. Based on the analysis of operating mode and ac equivalent model of the converter, backflow power is indirectly characterized by the phase-shift angle of the resonant network voltage and current. Based on this, this article analyzes the internal relationship between resonant parameters and backflow power to reduce backflow power by optimizing resonant parameters. Under the setting operating conditions, converter can achieve zero voltage switching (ZVS) switching, voltage gain conditions, and minimum backflow power. Compared with the existing methods, the proposed optimization method avoids additional auxiliary circuits and control complexity, improves the stability of the circuit. Experimental results verify the accuracy and feasibility of the theoretical analysis.
15 June 2020 in IEEE Access
When an input terminal is connected to a solar panel with a low voltage level and large power range fluctuation, a Boost type CLLC converter controlled by fixed frequency pulse width modulation (PWM) reduces the utilization of PV electric energy, and the synchronous drive of the secondary side and primary side ensures that the converter operates with low efficiency when the duty cycle is shifted by 0.5. To maximize the utilization of photovoltaic (PV) energy in a PV power generation system and improve the conversion efficiency, this paper studies a Boost CLLC converter with high gain and soft switching controlled by PWM-pulse frequency modulation (PFM) hybrid modulation for PV power generation. By controlling the duty cycle and switching frequency of the primary MOSFETs, the converter can stabilize the output voltage while tracking the PV maximum power point. Under such a hybrid control, the resonant gain of the converter is greater than 1, the voltage gain is large, one of the MOSFETs at the primary side is in a zero-voltage-switching-open (ZVS-ON) state, two diodes are used to realize zero-current-switching (ZCS) soft switching on the secondary side, and the efficiency of the converter is high. In addition, this paper studies the phenomenon of backflow power in the resonant circuit and the influence of a change in the switching frequency on the magnitude of the backflow power. Finally, a 500W experimental prototype was constructed to verify the accuracy of the theoretical analysis and the feasibility of the control method.
9 October 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Discontinuous pulse width modulation (DPWM) is widely used in three-level AC/DC converters due to its higher efficiency. For dual-output load applications, the vector synthesis error caused by the unbalanced NP voltage results in severe input current distortion with conventional DPWM. Moreover, the computational burden is further aggravated by the complicated subsector identification and dwelling time calculation resulting from partial vector redistribution after considering unbalanced NP voltage. In this article, modified subsector division and clamping modes are analyzed to eliminate vector synthesis errors. Then, an optimized carrier-based discontinuous pulse width modulation (OCB-DPWM) scheme with simple zero-sequence components (ZSCs) injection is proposed. Thus, the input current distortion under unbalanced NP voltages can be effectively suppressed. Compared with the modulation method with adjusting the NP voltage, which results in additional switching operations, the switching loss can be effectively reduced. In addition, the calculation of the ZSCs is extremely simple, and the program execution time is reduced by more than 60% compared with the existing modulation method. Finally, the simulation and experimental results of the Vienna rectifier are presented to validate the performance in terms of improved current THD and switching loss with different load conditions.
3 June 2022 in IEEE Transactions on Power Electronics
A secondary-side semiactive three-phase interleaved (SS-SA3PI) resonant converter employing a multimode modulation scheme for fast EV charger applications is proposed. A multimode modulation scheme is used to widen the output voltage range without dynamic switching problems. By using secondary-side semiactive control, the resonant converter does not need to operate in the fs < fr state to achieve boost operation. The minimum switching frequency of the converter is equal to the resonant frequency, which reduces the size of the magnetic components. Thus, the power density of the converter is improved. Compared with the traditional 3-phase interleaved LLC converter controlled by PFM, this converter widens the output voltage range without adding any circuit components. This article introduces the control mode, working principle and characteristics of the proposed converter in detail. A 10 kW experimental prototype is built to realize the output voltage of 100–1000V, which verifies the feasibility and effectiveness of the scheme.
19 April 2024 in IEEE Transactions on Industrial Electronics
Isolated dc/dc converters play a pivotal role in the realm of power electronics, particularly in the context of electric vehicle (EV) fast charging. These converters are responsible for delivering high-voltage direct current to EVs, sourced from a three-phase power factor correction converter, and exhibit compatibility with both low-voltage and high-voltage vehicle batteries. However, in many instances, the demand for constant power charging in various applications results in a significant portion of the transformer volume, thereby leading to a decrease in converter power density. This article presents a new analysis and design for a converter based on secondary-side semi-active (SSSA) control. This analysis provides theoretical support for transformer volume reduction and power density increase. It employs SSSA control to transfer stored energy from the transformer to the resonant network during boost operation, even when f s > f r , with the excitation inductance participating in resonance. Based on this analysis, the design of a 20-kW 650–850 V input to 300–900 V with 66.7A max output prototype is discussed. The objective is to achieve the highest feasible converter power density. The designed results confirm that the 2*PQ6535 (or 1*PQ6549) core can effectively serve the 20-kW transformer, resulting in an ultra-high power density of 14.36 kW/L (235W/in 3 ).