Vasanth Gopal

Mr. Vasanth Gopal

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2021 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
NSNeera Singh
Neera Singh
RURaghunandan Ummethala
Raghunandan Ummethala
PKPhani Shashanka Karamched
Phani Shashanka Karamched
RSRathinavelu Sokkalingam
Rathinavelu Sokkalingam
VGVasanth Gopal
Vasanth Gopal
KPKonda Gokuldoss Prashanth
Konda Gokuldoss Prashanth

11 May 2023 in BMC Oral Health
Verified
Journal Article
Open access
PDF file
APAshwini K patil
Ashwini K patil
DJDavidson Jebaseelan
Davidson Jebaseelan
DBDaniel Bomze
Daniel Bomze
VGVasanth Gopal
Vasanth Gopal
Objective: The study aims to evaluate the wear surface using 3D surface roughness and other material characterization of zirconia fabricated using photopolymerization based Lithography-based Ceramic Manufacturing (LCM). Method: LCM technology was used to fabricate zirconia specimens of size 10 × 10 × 2mm3. Scanning Electron Microscope, 3D–profilometer, X-ray Diffraction, and hardness test characterized the samples before and after wear and Coefficient of friction (COF) was monitored. Result: The COF was around 0.7 and did not differ much between the horizontally and vertically printed specimens. However, the surface roughness after wear for horizontally printed specimen was 0.567 ± 0.139 μm, while that for vertically printed specimen was 0.379 ± 0.080 μm. The reduced valley depth and the dale void volume were low for the vertically printed zirconia specimen, indicating lesser voids and low fluid retention. In addition, it was observed that the hardness value of the vertically printed sample was better. The scanning electron microscopic images and 3D surface profiles of the zirconia specimens depicted the surface topography and revealed the wear track. Conclusion: The study shows that zirconia fabricated using LCM technology possesses surface roughness of about 0.5 μm with no machining scars that are usually associated with CAD/CAM dentistry and also indicating agreement with clinically acceptable values for minimal surface roughness of dental restorations. Dental restorations using LCM fabricated zirconia redues the requirement of post-processing work flow that is part of CAD/CAM dentistry.

14 June 2019 in Materials
Verified
Journal Article
Open access
PDF file
VGVasanth Gopal
Vasanth Gopal
SGSneha Goel
Sneha Goel
Geetha ManivasagamGeetha Manivasagam
Geetha Manivasagam
SJShrikant Joshi
Shrikant Joshi
Ceramic coatings on metallic implants are a promising alternative to conventional implants due to their ability to offer superior wear resistance. The present work investigates the sliding wear behavior under bovine serum solution and indentation crack growth resistance of four coatings, namely (1) conventional powder-derived alumina coating (Ap), (2) suspension-derived alumina coating (As), (3) composite Al2O3—20wt % Yittria stabilized Zirconia (YSZ) coating (AsYs) deposited using a mixed suspension, and (4) powder Al2O3—suspension YSZ hybrid composite coating ApYs developed by axial feeding plasma spraying, respectively. The indentation crack growth resistance of the hybrid coating was superior due to the inclusion of distributed fine YSZ particles along with coarser alumina splats. Enhanced wear resistance was observed for the powder derived Ap and the hybrid ApYs coatings, whereas the suspension sprayed As and AsYs coatings significantly deteriorated due to extensive pitting.

29 December 2022 in Bioengineering
Verified
Journal Article
Open access
PDF file
PKPearlin Amaan Khan
Pearlin Amaan Khan
ATAravind Kumar Thoutam
Aravind Kumar Thoutam
VGVasanth Gopal
Vasanth Gopal
AGAswin Gurumallesh
Aswin Gurumallesh
Shrikant JoshiShrikant Joshi
Shrikant Joshi
Geetha ManivasagamGeetha Manivasagam
Geetha Manivasagam
Axial suspension plasma spraying (ASPS) is an alternative technique to atmospheric plasma spraying (APS), which uses a suspension of much finer powders (<5-micron particle size) as the feedstock. It can produce more refined microstructures than APS for biomedical implants. This paper highlights the influence of incorporated graphene nanoplatelets (GNPs) on the behavior of ASPS hydroxyapatite (HAp) coatings. The characterization of the ASPS coatings (HAp + varying GNP contents) was carried out using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), confocal Raman microscopy (CRM), white light interferometry (WLI), and contact angle measurements. The evaluation of the mechanical properties such as the hardness, roughness, adhesion strength, and porosity was carried out, along with a fretting wear performance. Additionally, the biocompatibility of the Hap + GNP coatings was evaluated using cytotoxicity testing which revealed a decrease in the cell viability from 92.7% to 85.4%, with an increase in the GNP wt.%. The visualization of the cell’s components was carried out using SEM and Laser Scanning Microscopy. Furthermore, the changes in the genetic expression of the various cellular markers were assessed to analyze the epigenetic changes in human mesenchymal stem cells. The gene expression changes suggested that GNPs upregulated the proliferation marker and downregulated the pluripotent markers by a minimum of three folds.

12 August 2026 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
SAS. Arulvel
S. Arulvel
JKJayakrishna Kandasamy
Jayakrishna Kandasamy
PKP. Kumaravelu
P. Kumaravelu
PRP. Promoth Raja
P. Promoth Raja
RNRamakrishnan Nathan
Ramakrishnan Nathan
VGVasanth Gopal
Vasanth Gopal
The present study explores the effect of an electrodeposited nickel layer on Inconel-718 alloy produced using different additive manufacturing (AM) routes, like Laser Powder Bed Fusion (L-PBF), Electron Beam Powder Bed Fusion (EB-PBF), and Laser-Directed Energy Deposition (L-DED). Comparative analyses were conducted by characterizing the physical, mechanical, and surface properties of Ni-coated AM-built Inconel-718 alloy surfaces. Different microstructures of Ni coatings were observed for different AM-built surfaces of Inconel-718 alloy. Influence on the Ni-layer hardness was also noted, plausibly as a consequence of variations in the residual stress of coated specimens. The hardness of Ni-coated specimens was not correlated well with the scratch resistance due to the unique natures of the Ni layer interface with the substrate surface, depending upon the AM route adopted to produce the Inconel-718 alloy builds. A comprehensive analysis of the scratch failure in identically coated specimens built using different AM routes has also been discussed.