Copper nanoparticles (CuNPs) can offer an alternative to conventional copper bactericides and possibly slow down the development of bacterial resistance. This will consequently lower the accumulation rate of copper to soil and water and lower the environmental and health burden imposed by copper application. Physical and chemical methods have been reported to synthesize CuNPs but their use as bactericides in plants has been understudied. In this study, two different CuNPs products have been developed, CuNP1 and CuNP2 in two respective concentrations (1500 ppm or 300 ppm). Both products were characterized using Dynamic Light Scattering, Transmission Electron Microscopy, Attenuated Total Reflection measurements, X-ray Photoelectron Spectroscopy, X-ray Diffraction and Scattering, and Laser Doppler Electrophoresis. They were evaluated for their antibacterial efficacy in vitro against the gram-negative species Agrobacterium tumefaciens, Dickeya dadantii, Erwinia amylovora, Pectobacterium carotovorum, Pseudomonas corrugata, Pseudomonas savastanoi pv. savastanoi, and Xanthomonas campestris pv. campestris. Evaluation was based on comparisons with two commercial bactericides: Kocide (copper hydroxide) and Nordox (copper oxide). CuNP1 inhibited the growth of five species, restrained the growth of P. corrugata, and had no effect in X. c. pv campestris. MICs were significantly lower than those of the commercial formulations. CuNP2 inhibited the growth of E. amylovora and restrained growth of P. s. pv. savastanoi. Again, its overall activity was higher compared to commercial formulations. An extensive in vitro evaluation of CuNPs that show higher potential compared to their conventional counterpart is reported for the first time and suggests that synthesis of stable CuNPs can lead to the development of low-cost sustainable commercial products.

The spin-pumping mechanism is probed through a tunnelling MgO interlayer in Fe/Pt bilayers. We show by ferromagnetic resonance technique and spin-pumping experiments that spin currents can tunnel through the MgO interlayer for thicknesses up to 2 nm and can produce significant voltages in the Pt layer. The electrical detection of spin-pumping furthermore reveals the critical role of rectification and shunting effects on the generated voltages. The non-zero spin current transport through a few monolayers of an insulating interlayer might initiate further studies on the role of very thin oxides in spin-pumping experiments.

IrO₂/Ir(Ni) film electrodes of variable Ni content have been prepared via a galvanic replacement method, whereby surface layers of pre-deposited Ni are replaced by Ir, followed by electrochemical anodization. Electrodeposition of Ni on a glassy carbon electrode support has been carried out at constant potential and the charge of electrodeposited Ni controlled so as to investigate the effect of precursor Ni layer thickness on the electrocatalytic activity of the corresponding IrO₂/Ir(Ni)/GC electrodes for the oxygen evolution reaction (OER). After their preparation, these electrodes were characterized by microscopic (SEM) and spectroscopic (EDS, XPS) techniques, revealing the formation of Ir deposits on the Ni support and a thin IrO₂ layer on their surfaces. To determine the electroactive surface area of the IrO₂ coatings, cyclic voltammograms were recorded in the potential range between hydrogen and oxygen evolution and the charge under the anodic part of the curves, corresponding to Ir surface oxide formation, served as an indicator of the quantity of active IrO₂ in the film. The electrocatalytic activity of the coatings for OER was investigated by current–potential curves under steady state conditions, revealing that the catalysts prepared from thinner Ni films exhibited enhanced electrocatalytic performance.

The thermoelectric materials community has made significant progress on nanostructured and processable materials to improve efficiency and flexibility, reducing manufacturing costs. Selenide compounds, such as Ag₂Se and Cu₂Se, have received a lot of attention because of their promising capabilities in thermoelectric applications. Additionally, Se is significantly more abundant than Te, with approximately ten times higher availability. High-energy ball milling (HEBM) process is a powerful solid-state synthesis/powder mechanical alloying method. The objective of this work is to form selenide compounds at different milling times (1–20 h) by HEBM process. The structural characterization of the compounds was studied by X-ray Diffraction and X-ray Photoelectron Spectroscopy, while the thermal stability of the prepared samples was examined by Thermogravimetric Analysis. The experimental results show that the Ag₂Se sample synthesized at 20 h presents lower thermal stability because of the higher specific surface area and the increased porosity as a result of the hardening effect. Additionally, Cu₂Se presents Cu₂O(SeO₃) as the main phase at low temperatures, while at higher temperatures, CuO is the dominant phase. Therefore, as the heating temperature increases, there is a complete evaporation of Se and a conversion of the remaining copper into copper oxide. The present study demonstrates a simple method for the synthesis of Ag₂Se and Cu₂Se thermoelectric materials with high oxidation resistance.

Lignin is one of the main structural components of lignocellulosic biomass and can be utilized to produce phenolic compounds that can be converted downstream to cycloalkanes and aromatics, which are useful as drop-in road or aviation biofuels. Within this study, the hydrodeoxygenation of model phenolic/aromatic compounds and surrogate mixture simulating the light fraction of lignin fast-pyrolysis bio-oil was performed under mild reaction conditions. Ni/BEA zeolite was selected as a catalyst to investigate the conversion and the product selectivity of alkyl phenols (phenol, catechol, cresols), methoxy-phenols (guaiacol, syringol, creosol), aromatics (anisole, 1,2,3-trimethoxybenzene) and dimer (2-phenoxy-1-phenyl ethanol) compounds towards (alkyl)cycloalkanes. The hydrodeoxygenation of a surrogate mixture of eleven phenolic and aromatic compounds was then studied by investigating the effect of reaction conditions (temperature, time, H₂ pressure, surrogate mixture concentration, and catalyst-to-feed ratio). The conversion of model compounds was in the range of 80–100%, towards a 37–81% (alkyl)cycloalkane yield, being strongly dependent on the complexity/side-chain group of the phenolic/aromatic ring. Regarding the hydrodeoxygenation of the surrogate mixture, 59–100% conversion was achieved, with up to a 72% yield of C₆–C₉ cycloalkanes. Characterization of spent catalysts showed that the hydrodeoxygenation of surrogate mixture led to carbonaceous depositions on the catalyst, which can be limited under lower temperatures and longer reaction conditions, while after regeneration, the physicochemical properties of catalysts can be partially recovered.