The need for technological development to reduce the impact of air pollution caused by ships has been strongly emphasized by many authorities, including the International Maritime Organization (IMO). This has encouraged research to develop an electric propulsion system using hydrogen fuel with the aim of reducing emissions from ships. This paper describes the test bed we constructed to compare our electric propulsion system with existing power sources. Our system uses hybrid power and a diesel engine generator with a combined capacity of 180 kW. To utilize scale-down methodology, the linear interpolation method is applied. The proposed hybrid power source consists of a molten carbonate fuel cell (MCFC), a battery, and a diesel generator, the capacities of which are 100 kW, 30 Kw, and 50 kW, respectively. The experiments we conducted on the test bed were based on the outcome of an analysis of the electrical power consumed in each operating mode considering different types of merchant ships employed in practice. The output, fuel consumption, and CO2 emission reduction rates of the hybrid and conventional power sources were compared based on the load scenarios created for each type of ship. The CO2 emissions of the hybrid system was compared with the case of the diesel generator alone operation for each load scenario, with an average of 70%~74%. This analysis confirmed the effectiveness of using a ship with a fuel-cell-based hybrid power source.
For developing national maritime traffic routes through the coastal waters of Korea, the customary maritime traffic flow must be accurately identified and quantitatively evaluated. In this study, the occupancy time of ships in cells was calculated through a density analysis based on automatic identification system data. The density map was statistically created by logarithmically transforming the density values and adopting standard deviation-based stretch visualization to increase the normality of the distribution. Many types of traffic routes such as open-sea, coastal, inland, and coastal access routes were successfully identified; moreover, the stretch color ramp ratio was reduced to identify routes having relatively high density. Adopting a single standard deviation and demonstrating the top 25% of color ramps, the analysis afforded the main routes through which customary traffic flows. This novel density analysis method and statistical visualization method is expected to be used for developing national maritime traffic routes and should ultimately contribute to maritime safety. Moreover, it provides a scientific means and simulator for determining the navigation area and analyzing conflicts with other activities in marine spatial planning.
Since recent marine application of fuel cell systems has been due largely limited to small-sized ships, this paper was aimed to investigate the technical applicability of molten carbonate fuel cell (MCFC) for medium and large-sized ships, using a 180 kW class hybrid test bed with combined power sources: A 100 kW MCFC, a 30 kW battery and a 50 kW diesel generator. This study focused primarily on determining whether the combined system designed in consideration of actual marine power system configuration could function properly. A case study was conducted with a 5500 Twenty-foot Equivalent Unit (TEU) container vessel. The operation profile was collected and analyzed in order to develop electric load scenarios applicable to the power system. Throughout the experiment, we evaluated the power quality of the voltage and frequency in the process of synchronization and de-synchronization across the power sources. Therefore, research results revealed that power quality continued to be excellent. This outcome provides insight into the technical reliability of MCFC application on large marine vessels.
In the case of the electric propulsion system on the vessel, Diode Front End (DFE) rectifiers have been applied for large-sized ships and Active Front End (AFE) rectifiers have been utilized for small and medium-sized ships as a part of the system. In this paper, we design a large electric propulsion ship system using AFE rectifier with the proposed phase angle detector and verify the feasibility of the system by simulation. The phase angle derived from the proposed phase angle detection method is applied to the control of the AFE rectifier instead of the zero-crossing method used to detect the phase angle in the control of the conventional AFE rectifier. We compare and analyze the speed control, Direct Current (DC)-link voltage, harmonic content and measurement data of heat loss by inverter switch obtained from the simulation of the electric propulsion system with the 24-pulse DFE rectifier, the conventional AFE rectifier, and the proposed AFE rectifier. As a result of the simulation, it was confirmed that the proposed AFE rectifier derives a satisfactory result similar to that of a 24-pulse DFE rectifier with a phase shifting transformer installed according to the speed load of the ship, and it can be designed and applied as a rectifier of a large-sized vessel.
31 December 2021 in Journal of Advanced Marine Engineering and Technology
This research showcases the seamless integration of solid oxide fuel cells (SOFC) with waste heat recovery systems, utilizing liquefied petroleum gas (LPG) as the primary fuel source. The focus of the study is on efficiently harnessing the cold energy from the LPG supply to produce substantial power for the entire system. To optimize energy utilization, a gas turbine (GT) and steam Rankine cycle (SRC) are integrated to effectively convert waste heat from the system into useful work and power. Additionally, a waste heat boiler (WHB) is incorporated to provide superheated vapor steam for seafarer accommodation. A detailed thermodynamic analysis and investigation of the proposed integrated system are performed. The simulations and optimizations of combined system are conducted using ASPEN HYSYS V12.1. Thermodynamic equations based on the fundamental laws of thermodynamics are employed to estimate system performance indicators, and the exergy destruction in major components is assessed to optimize the system’s design and operation. The proposed system exhibits impressive energy and exergy efficiencies, calculated at 52.65% and 51.10%, respectively. Moreover, the waste heat recovery combined cycles contribute an additional 1,759.73 kW, equivalent to 31.65% of the total system output. The innovative models are validated against experimental data from the literature, demonstrating strong agreement. Furthermore, a comprehensive parametric study investigates the influence of varying the current density from 900 to 1,950 A/m2, leading to a total energy efficiency variation of 41.59%, ranging from 82.45% to 40.86%. The organic Rankine cycle (ORC) performs exceptionally well, capitalizing on both cold energy and high‐temperature waste heat to achieve high energy recovery efficiency. The WHB is capable of providing 8,200 kg/h of superheated vapor stream at 151°C and 499 kPa for seafarer accommodation and heating purposes. The economic viability analysis is conducted to assess the potential for investment, maintenance costs, and the payback period associated with the proposed system.