Estela Garcez

Dr. Estela Garcez

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2020 in Construction and Building Materials
Verified
Journal Article
Closed access
AMAlastair MacLeod
Alastair MacLeod
AFAndras Fehervari
Andras Fehervari
WGWill P. Gates
Will P. Gates
EGEstela Garcez
Estela Garcez
LALaurie P. Aldridge
Laurie P. Aldridge
Frank CollinsFrank Collins
Frank Collins

26 May 2023 in Materials
Verified
Journal Article
Open access
PDF file
RNRahnum Tasnuva Nazmul
Rahnum Tasnuva Nazmul
BSBre-Anne Sainsbury
Bre-Anne Sainsbury
Safat Al-DeenSafat Al-Deen
Safat Al-Deen
EGEstela Garcez
Estela Garcez
Mahmud AshrafMahmud Ashraf
Mahmud Ashraf
The construction industry is facing increased demand for adopting sustainable ‘green’ building materials to minimise the carbon footprint of the infrastructure sector to meet the United Nations 2030 Sustainability Goals. Natural bio-composite materials such as timber and bamboo have been widely used in construction for centuries. Hemp has also been used in different forms in the construction sector for decades for its thermal and acoustic insulation capability owing to its moisture buffering capacity and thermal conductivity. The current research aims to explore the possible application of hydrophilic hemp shives for assisting the internal curing of concrete materials as a biodegradable alternative to currently used chemical products. The properties of hemp have been assessed based on their water absorption and desorption properties associated with their characteristic sizes. It was observed that, in addition to its excellent moisture absorption capacity, hemp released most of its absorbed moisture into the surroundings under a high relative humidity (>93%); the best outcome was observed for smaller hemp particles (<2.36 mm). Furthermore, when compared to typical internal curing agents such as lightweight aggregates, hemp showed a similar behaviour in releasing its absorbed moisture to the surroundings indicating its potential application as a natural internal curing agent for concrete materials. An estimate of the volume of hemp shives required to provide a similar curing response to traditional internal curing techniques has been proposed.

24 October 2023 in Construction and Building Materials
Verified
Journal Article
Open access
RNRahnum T. Nazmul
Rahnum T. Nazmul
BSBre-Anne Sainsbury
Bre-Anne Sainsbury
EGEstela Garcez
Estela Garcez
SASafat Al-Deen
Safat Al-Deen
Mahmud AshrafMahmud Ashraf
Mahmud Ashraf

18 September 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Sukanta Kumer ShillSukanta Kumer Shill
Sukanta Kumer Shill
EGEstela Garcez
Estela Garcez
Safat Al-DeenSafat Al-Deen
Safat Al-Deen
Mahbube SubhaniMahbube Subhani
Mahbube Subhani
Foam concrete has been used in various real-life applications for decades. Simple manufacturing methods, lightweight, high flowability, easy transportability, and low cost make it a useful construction material. This study aims to develop foam concrete mixtures for various civil and geotechnical engineering applications, such as in-fill, wall backfill and soil replacement work. A blended binder mix containing cement, fly ash and silica fume was produced for this study. Its compressive strength performance was compared against conventional general purpose (GP) cement-based foam concrete. Polypropylene (PP) fibre was used for both mixtures and the effect of various percentages of foam content on the compressive strength was thoroughly investigated. Additionally, two types of foaming agents were used to examine their impact on density, strength and setting time. One foaming agent was conventional, whereas the second foaming agent type can be used to manufacture permeable foam concrete. Results indicate that an increase in foam content significantly decreases the strength; however, this reduction is higher in GP mixes than in blended mixes. Nevertheless, the GP mixes attained two times higher compressive strength than the blended mix’s compressive strengths at any foam content. It was also found that the foaming agent associated with creating permeable foam concrete lost its strength (reduced by more than half), even though the density is comparable. The compressive stress–deformation behaviour showed that densification occurs in foam concrete due to its low density, and fibres contributed significantly to crack bridging. These two effects resulted in a long plateau in the compressive stress–strain behaviour of the fibre-reinforced foam concrete.


23 July 2020 in Materials
Verified
Journal Article
Open access
PDF file
ARAbrahão Bernardo Rohden
Abrahão Bernardo Rohden
JCJessica Regina Camilo
Jessica Regina Camilo
RARafaela Cristina Amaral
Rafaela Cristina Amaral
EGEstela Garcez
Estela Garcez
Monica GarcezMonica Garcez
Monica Garcez
This paper investigates a potential application of hard-to-recycle plastic waste as polymeric addition in high strength concrete, with a focus on the potential to mitigate heat-induced concrete spalling and the consequent effects on the mechanical properties. The waste corresponds to soft and hard plastic, including household polymers vastly disposed of in landfills, although technically recyclable. Mechanical and physical properties, cracking, mass loss, and the occurrence of spalling were assessed in high strength concrete samples produced with either plastic waste or polypropylene fibers after 2-h exposure to 600 °C. The analysis was supported by Scanning Electron Microscopy and X-Ray Computed Tomography images. The plastic waste is composed of different polymers with a thermal degradation between 250 to 500 °C. Polypropylene (PP) fibers and plastic waste dispersed in concrete have proved to play an essential role in mitigating heat-induced concrete spalling, contributing to the release of internal pressure after the polymer melting. The different morphology of plastic waste and polypropylene fibers leads to distinct mechanisms of action. While the vapor pressure dissipation network originated by polypropylene fibers is related to the formation of continuous channels, the plastic waste seems to cause discontinuous reservoirs and fewer damages into the concrete matrix. The incorporation of plastic waste improved heat-induced concrete spalling performance. While 6 kg/m3 of plastic increased the mechanical performance after exposure to high temperature, the incorporation of 3 kg/m3 resulted in mechanical properties comparable to the reference concrete.