Archimedes screw turbines are considered a new technology in small- or microscale hydropower. Archimedes screw turbines are easy and practical to operate. However, their manufacturing presents some challenges owing to their screw-shaped design. Most of the previous works on Archimedes screw turbines focused on the turbines’ design, while limited studies were found on their manufacturing processes. In addition, no review work was found on the manufacturability of the Archimedes screw turbine. Hence, this work aims to address this gap by reviewing the various manufacturing methods of Archimedes screw turbines. Moreover, one of the objectives of the study is to assess the sustainable manufacturability of the Archimedes screw turbine. The results show that Archimedes screw turbines are mainly manufactured using conventional manufacturing methods for larger turbines and 3D printers for relatively smaller ones. Traditional methods of manufacturing entailed high skill proficiency, while 3D-printing methods for Archimedes screw turbines are still in their early developmental stages. Sustainable assessment studies have identified additive manufacturing as having a relatively lower environmental impact than conventional manufacturing on turbine blades. These trade-offs must be accounted for in the design and development of Archimedes screw turbines. Moreover, integrating sustainability assessment and the employment of Industry 4.0 enables the smart production and sustainable assessment of AST manufacturability.

5G wireless devices are expected to be the main cause of the rapid increase in Internet traffic. One of the solutions is to develop the mobile devices that can deal with local traffic directly instead of conveying data through a base station. Then, the mobile devices act in a way that they can meet either infrastructure or ad hoc D2D mode communications requirements. This paper aims to design joint operation protocol of the routing control and group key agreement based on the idea that the dual operation of infrastructure and ad hoc D2D mode communications in the same wireless device requires the ad hoc node to rely on the network layer function as small as possible. In this paper, we propose the ad hoc D2D protocol to control the ad hoc D2D network and manage the group key in self-organized group of ad hoc nodes based on their home IP addresses wherever they move. Finally, this paper analyzes the latency time for the group key agreement process, which can show the tolerable size of the ad hoc network running with the group key agreement process.

The existing LTE mobile system uses the vertical model to handle the session-based security management. However, the goal of this paper is to propose a packet key-based security management scheme on the blockchain control plane to enhance the existing session key-based security scheme and overcome the limitation that the existing vertical model, as well as the Software-Defined Networking (SDN) based horizontal model, confronts within solving end-to-end security management. The proposed blockchain-based security management (BSM) scheme enables each peer to easily obtain the necessary parameters required to manage the packet key-based security system. The important features of the BSM scheme include the renewal process, which enables the different packet data streams to use completely different security parameters for the security management. In addition, because even blind values cannot be exposed to the possible attackers, our BSM scheme guarantees very secure end-to-end data transfer against active attacks such as falsification of data and transactions. Finally, this paper compares the BSM scheme with the existing vertical model to prove the advantageous effects on latency.

Full-mesh IPSec tunnels pass through a black ("un secure") network (B-NET) to any red ("secure") networks (R NETs). These are needed in military environments, because they enable dynamically changing R-NETs to be reached from a B NET. A dynamically reconfiguring security policy database (SPD) is very difficult to manage, since the R-NETs are mobile. This paper proposes advertisement process technologies in association with the tunnel gateway's protocol that sends 'hello' and 'prefix advertisement (ADV)' packets periodically to a multicast IP address to solve mobility and security issues. We focus on the tunnel gate way's security policy (SP) adaptation protocol that enables R-NETs to adapt to mobile environments and allows them to renew services rapidly soon after their redeployment. The prefix ADV process enables tunnel gateways to gather information associated with the dynamic changes of prefixes and the tunnel gateway's status (that is, 'down'/restart). Finally, we observe two different types of performance results. First, we explore the effects of different levels of R-NET movements on SP adaptation latency. Next, we derive the other SP adaptation latency. This can suffer from dynamic deployments of tunnel gateways, during which the protocol data traffic associated with the prefix ADV protocol data unit is expected to be severe, especially when a certain tunnel gateway restarts.