In this work silica (SiO2) and sulfonic acid-functionalized silica (sul-SiO2) were synthesized by sol–gel method from tetraethoxysilane (TEOS) and 3-mercatopropyltrimethoxysilane (MPTMS) with various ratios between them. The synthesized materials were characterized by x-ray diffraction (XRD) for crystalline structure, Brunauer–Emmet–Teller (BET) specific surface area analysis, transmission electronic microscopy (TEM) and dynamic light scattering (DLS) for particle size analysis, and ion exchange capacity (IEC) for determining sulfur content in Sul-SiO2 materials. The initial results showed that the average particle size of amorphous SiO2 and Sul-SiO2 at different TEOS: MPTMS ratios are in narrow distribution with average diameter about 20–30 nm. The particle size of Sul-SiO2 is almost unaffected by the content of MPTMS while IEC depends strongly on it. Composite membranes of 60 μm thickness were successfully prepared from blending of poly(vinylidene fluoride) (PVDF) and synthesized amorphous SiO2. It was shown that the latter may be used as a reinforced phase for composite membrane electrolytes based on PVDF.

A new facile template-free method is presented to synthesize Fe-treated N-doped carbon (Fe/N–C) catalysts for oxygen reduction reaction (ORR) by employing a synthesis protocol of pyrolysis–leaching–stabilization (PLS) sequence of polypyrrole in the presence of ferric source, which serves dual purposes of an oxidant for pyrrole polymerization and an iron source. Each step in the PLS sequence is assessed in detail in terms of the related structural properties of the resulting carbon catalysts, and their effects on ORR activities are elaborated to confirm the validity of the current synthesis protocol. It is found that the as-prepared carbon catalyst exhibits outstanding high catalytic activity in both alkaline and acidic conditions. The carbon catalyst prepared at a pyrolysis temperature of 900 °C (FePPyC-900) shows remarkably high ORR activity with onset potential of 0.96 V (vs. RHE), which is similar to that of Pt/C, whereas the half-wave potential (E_1/2) of FePPyC-900 is 0.877 V, more positive than that of Pt/C at the same catalyst loading amount under alkaline conditions. Furthermore, the FePPyC-900 catalyst also illustrates exceptionally high activity under acidic conditions with onset and half-wave potentials of 0.814 and 0.740 V, respectively, which are almost comparable to those (0.817 and 0.709 V) of the state-of-the-art Pt/C catalyst, which is rarely observed for non-Pt-based carbon catalysts. In addition, the FePPyC-900 catalyst displays much better stability and methanol tolerance than the Pt/C and exhibits a four electron transfer pathway under both alkaline and acidic conditions. Such extraordinary high ORR activity and stability of the FePPyC-samples can be attributed to the implementation of extra stabilization step in addition to conventional sample preparation steps of pyrolysis and subsequent leaching in current PLS synthesis protocol as well as to the use of highly conducting PPy as a single precursor of carbon and nitrogen in the presence of Fe.

The lifespan of lithium (Li) metal batteries (LMBs) can be greatly improved by the formation of inorganic‐rich electrode‐electrolyte interphases (EEIs) (including solid‐electrolyte interphase on anode and cathode‐electrolyte interphase on cathode). In this work, a localized high‐concentration electrolyte containing lithium bis(fluorosulfonyl)imide (LiFSI) salt, 1,2‐dimethoxyethane (DME) solvent and 1,2‐bis(1,1,2,2‐tetrafluoroethoxy)ethane (BTFEE) diluent is optimized. BTFEE is a fluorinated ether with weakly‐solvating ability for LiFSI so it also acts as a co‐solvent in this electrolyte. It can facilitate anion decomposition at electrode surfaces and promote the formation of more inorganic‐rich EEI layers. With an optimized molar ratio of LiFSI:DME:BTFEE = 1:1.15:3, LMBs with a high loading (4 mAh cm ⁻² ) lithium nickel manganese cobalt oxide (LiNi _0.8 Mn _0.1 Co _0.1 ) cathode can retain 80% capacity in 470 cycles when cycled in a voltage range of 2.8–4.4 V. The fundamental understanding on the functionality of BTFEE revealed in this work provides new perspectives on the design of practical high‐energy density battery systems.

The amount of Fe and NH₃treatment significantly affect the structural and catalytic properties of resulting ZIF-derived Fe–N–C catalysts.