Ultrawide-bandgap gallium oxide (Ga 2 O 3 ) devices have recently emerged as promising candidates for power electronics; however, the low thermal conductivity ( k T ) of Ga 2 O 3 causes serious concerns about their electrothermal ruggedness. This letter presents the first experimental demonstrations of large-area Ga 2 O 3 Schottky barrier diodes (SBDs) packaged in the bottom-side-cooling and double-side-cooling configurations, and for the first time, characterizes the surge current capabilities of these packaged Ga 2 O 3 SBDs. Contrary to popular belief, Ga 2 O 3 SBDs with proper packaging show high surge current capabilities. The double-side-cooled Ga 2 O 3 SBDs with a 3 × 3-mm 2 Schottky contact area can sustain a peak surge current over 60 A, with a ratio between the peak surge current and the rated current superior to that of similarly-rated commercial SiC SBDs. The key enabling mechanisms for this high surge current are the small temperature dependence of on -resistance, which strongly reduces the thermal runaway, and the double-side-cooled packaging, in which the heat is extracted directly from the Schottky junction and does not need to go through the low- k T bulk Ga 2 O 3 chip. These results remove some crucial concerns regarding the electrothermal ruggedness of Ga 2 O 3 power devices and manifest the significance of their die-level thermal management.
1 April 2021 in IEEE Transactions on Power Electronics
Planar, double-side cooled power modules are emerging in electric-drive inverters because of their low profile, better heat extraction, and lower package parasitic inductances. However, there is still a concern about their reliability due to the rigid interconnection between the device chips and two substrates of the power module. In this article, a porous interposer made of low-temperature sintered silver is introduced to reduce the thermomechanical stresses in the module. A double-side cooled half-bridge module consisting of two 1200 V, 149 A SiC MOSFETs was designed, fabricated, and characterized. By using the sintered-Ag instead of solid copper interposers, our simulation results showed that, at a total power loss of 200 W, the thermomechanical stress at the most vulnerable interfaces (interposer-attach layer) was reduced by 42% and in the SiC MOSFET by 50% with a tradeoff of only 3.6% increase in junction temperature. The sintered-Ag interposers were readily fabricated into the desired dimensions without postmachining and did not require any surface finishing for die bonding and substrate interconnection by silver sintering. The porous interposers were also deformable under a low force or pressure, which helped to accommodate chip thickness and/or substrate-to-substrate gap variations in the planar module structure, thus simplifying module fabrication. The experimental results on the electrical performance of the fabricated SiC modules validated the success of using the porous silver interposers for fabricating planar, double-side cooled power modules.
8 May 2023 in IEEE Transactions on Power Electronics
Low-profile double-side cooled power modules are emerging in electric-drive inverters to achieve higher power density and efficiency. However, the rigid interconnection between the devices and two substrates raises the thermomechanical reliability issue of double-side cooled modules. In the prior work, we proposed the use of porous sintered-silver (Ag) interposers in the double-side cooled modules, resulting in reduced thermomechanical stresses, better heat extraction, and lower package parasitic inductance. To further improve the power density and demonstrate the benefits of using the sintered-Ag interposers, we proposed a revised half-bridge module layout that further reduced the power-loop parasitic inductance by 23%, improved the power handling capability by 44%, and retained a similar thermomechanical stress reduction. After carefully selecting high-temperature packaging materials, we fabricated the improved module layout with a reasonably high yield due to the deformable feature of sintered-Ag interposers. The thermal testing showed that the module had excellent power handling capability with a junction-to-fluid thermal resistance of 0.76 °C/W due to the double-sided cooling. The electrical characterization at elevated temperatures up to 250 °C and the switching characterization validated the functionalities of the power modules with SiC devices aimed for high-temperature and fast switching. Six of the double-side cooled power modules with sintered-Ag interposers were assembled into a segmented traction inverter, demonstrating a high power density of over 100 kW/L.
18 October 2021 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Although excellent reliability has been reported for sintered silver as a die-attach material under both thermal and power cycling loads in power electronics applications, the promise of this material as a large-area attachment at temperatures beyond 200 °C needs to be investigated. This article presents insights into the thermomechanical behavior and reliability of sintered silver under extreme thermal cycling conditions. In this study, we bonded sintered silver samples and subjected it to a thermal cycling profile of −40 °C to 200 °C with high ramp rates. We periodically monitored samples under thermal cycling to detect the presence of any failure mechanisms using a scanning acoustic microscope. We also included 95Pb5Sn solder in the study to obtain reference data. Results show the occurrence of cracks in sintered silver followed by a rapid rate of crack growth that exceeded the failure criterion in just 50 cycles. The predominant failure mechanism we observed was adhesive failure. As a large-area attachment, solder exhibited a higher reliability than sintered silver but failed within 100 cycles. Finally, we performed thermomechanical modeling to compute strain energy density values and correlated these with the experimentally observed crack growth rates to formulate a lifetime prediction model for sintered silver.
24 May 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Coupled inductors are used in power electronics to improve transient response and reduce component size. To further increase inductance density and reduce fringing fields, a combination of different magnetic materials was introduced to create a hetero-magnetic coupled inductor (HMCI) core. To simplify and speedup the prototyping of HMCI designs, in this study a paste-extrusion additive manufacturing platform was used to co-process a custom-developed magnetic and conductive feedstock. First, ferrite plates of each having a winding were co-printed and co-sintered. Then, the HMCI was assembled by bonding together the ferrite + winding plates using a low-temperature curable magnetic paste. The finished HMCI was characterized by measuring its dc winding resistances, leakage inductance, and coupling coefficient. The coupling coefficient of the HMCI was easily adjustable to meet various requirements for high-frequency interleaved multiphase buck converters. This work demonstrates the feasibility of applying an additive manufacturing process for rapid prototyping of an unconventional power magnetic component having an inhomogeneous magnetic core.
Soft magnetic moldable composites (SM 2 Cs) would be ideal for magnetic integration in power electronics converters because they can be readily processed at low temperature without pressure into the core shapes prescribed for the circuits. However, most of the existing SM 2 Cs have low relative magnetic permeability (<; 30) and low saturation flux density (<; 1 T). To improve the magnetic properties, we combined three different magnetic powders giving rise to a tri-modal size distribution and an acrylic polymer to produce a paste of tri-modal SM 2 C. The paste was molded and then cured below 200 °C without pressure to form cores offering a relative permeability over 30, a saturation flux density over 1.0 T, and a low core-loss density. The ease of its processing and high-performance properties make this SM 2 C a good candidate material for power electronics applications.