Sarah Saeed

Ms. Sarah Saeed


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 January 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SSSarah Saeed
Sarah Saeed
Jorge GarciaJorge Garcia
Jorge Garcia
Ramy GeorgiousRamy Georgious
Ramy Georgious
This article explores the use of a variable inductor as a reactive element for energy transfer in a dual-active-bridge (DAB) converter. By using a controlled variable inductor, the optimal switching region in the operation of the phase-shift DAB can be extended, and thus, high efficiencies can be achieved over wider load ranges compared to the traditional solution. Moreover, the combined use of the variable inductance together with the phase shift, as two control parameters, allows for the linearization of the DAB converter transfer function, which improves the stability and the performance of the controller. And finally, due to the controlled saturation of the device, it is feasible to reduce the magnetic core size, yielding a size optimization of the full converter. This article develops a circuit-based model to simulate the converter system, aiming to study the proposed improvements. Furthermore, a 2-kW SiC-based DAB converter prototype is constructed, including a controlled variable inductor. The experimental results presented in this article validate the studies carried out for the different operation conditions.

11 April 2020 in Energies
Verified
Journal Article
Open access
PDF file
SSSarah Saeed
Sarah Saeed
Ramy GeorgiousRamy Georgious
Ramy Georgious
Jorge GarciaJorge Garcia
Jorge Garcia
This paper proposes and develops a circuit-based model aiming to simulate variable magnetic power elements in power electronic converters. The derived model represents the magnetic element by a reluctance-based equivalent circuit. The model takes into consideration device core losses, with the main emphasis given to hysteresis losses, which are modeled using the Jiles-Atherton model. The core loss model is further validated on different ferromagnetic materials to prove its range of applicability. The winding losses of the magnetic device are also taken into consideration, which are obtained using Dowell empirical formulas. In addition, the frequency dependence of the device losses is also considered. The proposed modeling procedure has been applied to study and characterize a double E-core variable power inductor structure in a 1 kW SiC full bridge DC-DC converter. The procedure has been verified by comparing the simulation results to the experimental measurements, confirming the validity and accuracy of the full circuit-based model.

25 December 2020 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
SSSarah Saeed
Sarah Saeed
Jorge GarciaJorge Garcia
Jorge Garcia
MPMarina M. S. Perdigão
Marina M. S. Perdigão
VCValter S. Costa
Valter S. Costa
BBBruno Baptista
Bruno Baptista
Andre M. S. MendesAndre M. S. Mendes
Andre M. S. Mendes
This article presents a study to improve the inductance calculation of magnetic components in power converters, of particular interest, in the case of applications using variable inductors. In order to increase the accuracy of the estimation of the reluctance paths, several factors have been taken into consideration, such as the permeability definition under saturation, the temperature effect on the magnetic material behavior, and the distribution of saturated regions in the magnetic core. The methodology of the present study is to compare the analytical models derived from circuital equivalents against finite-element analysis numerical techniques, in order to validate the proposed model of a variable inductor, including the effects of the mentioned factors. The proposed model is then compared with experimental measurements to prove its validity. Finally, a design example for the variable inductor is presented.

11 April 2019 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
Jorge GarciaJorge Garcia
Jorge Garcia
SSSarah Saeed
Sarah Saeed
EGEmre Gurpinar
Emre Gurpinar
Alberto CastellazziAlberto Castellazzi
Alberto Castellazzi
PFPablo García Fernández
Pablo García Fernández
A novel implementation of an isolated gate driver for power switches is proposed in this study. The driver is bespoke designed for SiC power mosfet s. The proposal achieves the main driver characteristics—isolation capability, gate switching command, and power transfer to the secondary side by using a unique magnetic transformer. The resulting simple circuitry enables the integration of the driver into the power cell, achieving theoretical higher power density values of the final system. The principle of operation of the driver is described in detail. The original pulsewidth modulation signal is modulated with a pure ac square waveform under a two-level modulation scheme, that guarantees no saturation of the magnetic core. The signal is then magnetically coupled to the secondary side, where it is rectified and reconstructed to effectively drive the target device. In addition, the steps needed to provide a suitable design taking into account the parameters of the target power switch are also detailed. The resulting driver is characterized and a prototype of the driver is built and tested. The main results of the driver performance on a SiC mosfet -based prototype are presented. Based on the analysis of these results, this study experimentally demonstrates the feasibility of the proposal.

21 December 2017 in IEEE Transactions on Smart Grid
Verified
Journal Article
Open access
ANAngel Navarro-Rodriguez
Angel Navarro-Rodriguez
PFPablo García Fernández
Pablo García Fernández
Ramy GeorgiousRamy Georgious
Ramy Georgious
Jorge GarciaJorge Garcia
Jorge Garcia
SSSarah Saeed
Sarah Saeed
This paper proposes a novel solution for transient frequency compensation in weak 3-phase Microgrids (MGs) based on a Luenberger observer and a transient frequency detector. Unlike in conventional grids, the low inertia of the generators coupled to a MG could make their rotor speeds to be affected by load changes, varying the grid frequency and compromising the grid quality and stability. This problem has been approached in the literature by the Virtual Inertia (VI) concept. However, the existing solutions are affected by the decoupling of the grid frequency reference and the frequency estimation bandwidth. The proposed paper addresses these problems by the use of a transient frequency drift estimator based on a transient detector and a Luenberger type observer that provides a nearly-zero lag frequency estimation. The proposed alternative is analytically compared with the existing techniques and validated through simulation and exhaustive experimental results in an islanded MG. The developed method enables a 1Hz reduction in the transient frequency deviation when compared with the existing alternatives and improves the system stability.

19 July 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
RMRand Al Mdanat
Rand Al Mdanat
Ramy GeorgiousRamy Georgious
Ramy Georgious
SSSarah Saeed
Sarah Saeed
Jorge GarciaJorge Garcia
Jorge Garcia
Gallium nitride (GaN) high electron mobility transistors (HEMTs) show potential for high-efficiency power converters, but as switching frequencies increase, a need arises for analytical models to predict performance and estimate switching losses. This paper presents a precise and straightforward power loss model for high-voltage enhancement-mode GaN HEMTs, accounting for parasitic inductances, nonlinear junction capacitances, and transconductance. The model employs MATLAB to predict switching waveforms and compute total losses, and the accuracy is verified against experimental tests and LTspice simulations. Such a simple model with fewer operations and fast computations is advantageous when used in converter optimization problems, such as design optimization, where multiple variables are considered or real-time optimal control problems. It is worth noting that the increased switching speeds enabled by GaN devices pose challenges in measuring switching currents, which are critical for evaluating performance and computing losses in experimental tests. Conventional methods for switching current measurements have limited bandwidth or affect layout inductance. This study also explores the implications of integrating coaxial current shunts, commonly used for measuring current in fast-switching transistors, into the source path of transistors, comparing the circuit’s behaviour with and without the shunts.