Wroclaw University of Science and Technology, Faculty of Mechanical Engineering, Department of Machine Design and Research, 7/9 Łukasiewicza Str., 50-371 Wroclaw, Poland
Mr. Marek Mysior
Wroclaw University of Science and Technology, Faculty of Mechanical Engineering, Department of Machine Design and Research, 7/9 Łukasiewicza Str., 50-371 Wroclaw, Poland
A significant challenge in the utilization of alternative gaseous fuels is to use their energy potential at the desired location, considering economic feasibility and sustainability. A potential solution is a compression, transportation in pressure tanks, and generation of electricity and heat directly at the recipient. In this research, the potential for generating syngas from abundant waste substrates was analyzed. The sewage sludge (SS) was used as an example of a bulky and abundant resource that could be valorized via gasification, compression, and transport to end-users in containers. A model was developed, and theoretical analyses were completed to examine the influence of the calorific value of the syngas produced from the SS gasification (under different temperatures and gasifying agents) on the efficiency of energy transportation of compressed syngas. First, the gasification simulation was carried out, assuming equilibrium in a downdraft gasifier (reactor) from 973–1473 K and five gasifying agents (O2, H2, CO2, water vapor, and air). Molar ratios of the gasifying agents to the (SS) C ranged from 0.1–1.0. The model predicted syngas composition, lower calorific values (LHV) for a given molar ratio of the gasification agent, and compressibility factor. It was shown that the highest LHV was obtained at 0.1 molar ratio for all gasifier agents. The highest LHV (~20 MJ∙(Nm3)−1) was obtained by gasification with H2 and the lowest (~13 MJ∙(Nm3)−1) in the case of air. Next, the available syngas volume in a compressed gas transportation unit and the stored energy was estimated. The largest syngas volume can be transported when O2 is used as a gasifying agent, but the highest amount of transported energy was estimated for gasification with H2. Finally, the techno-economic analyses showed that syngas from SS could be competitive when the energy of compressed syngas is compared with the demand of an average residential dwelling. The developed syngas energy transport system (SETS) concept proposes a new method to distribute compressed syngas in pressure tanks to end-users using all modes of transport carrying intermodal ISO containers. Future work should include the determination of energy demand for syngas compression, including pressure losses, heat losses, and analysis of the influence of syngas on storage and compression devices.
A significant challenge in sustainability and development of energy systems is connected with limited diversity and availability of fuels, especially in rural areas. A potential solution to this problem is compression, transport, and storage of raw biogas, that would increase diversity and availability of energy sources in remote areas. The aim of this study was to perform experimental research on raw biogas compression concerning biogas volume that can be stored in a cylinder under the pressure of 20 MPa and to compare obtained results with numerical models used to describe the state of gas at given conditions. Results were used to determine the theoretical energy content of raw biogas, assuming its usage in CHP systems. In the study, six compression test runs were conducted on-site in an agricultural biogas plant. Compression time, pressure as well as gas volume, and temperature rise were measured for raw biogas supplied directly from the digester. Obtained results were used to evaluate raw biogas compressibility factor Z and were compared with several equations of state and numerical methods for calculating the Z-factor. For experimental compression cycles, a theoretical energy balance was calculated based on experimental results published elsewhere. As a result, gas compressibility factor Z for storage pressure of 20 MPa and a temperature of 319.9 K was obtained and compared with 6 numerical models used for similar gases. It was shown that widely known numerical models can predict the volume of compressed gas with AARE% as low as 4.81%. It was shown that raw biogas supplied directly from the digester can be successfully compressed and stored in composite cylinders under pressure up to 20 MPa. This proposes a new method to utilize raw biogas in remote areas, increasing the diversity of energy sources and increasing the share of renewable fuels worldwide.
31 March 2022 in Eksploatacja i Niezawodność – Maintenance and Reliability
The article presents the experimental strength evaluation of modular car trailers with a maximum permissible total mass of up to 3500 kg and its application to assess the mechanical strength of box-type car trailers. Tests were carried out using an original test bench dedicated to fatigue testing. They aimed to compare a trailer made in traditional technology with a trailer equipped with a load-carrying structure containing a sandwich panel. As a result of the conducted work, the displacement values of the measurement points were measured. The deformation form of the trailer made in the traditional technology was compared with the trailer containing the sandwich panel. The proposed method of experimental strength evaluation of modular car trailers enables a quantitative assessment of the mechanical strength of the load-carrying structures of trailers. This results in improved safety of trailer operation in road traffic by identifying the critical elements of the load-carrying structure at the early design phase before the trailer is allowed to run on the road.