Yucheng Fu

Dr. Yucheng Fu

Pacific Northwest National Laboratory, Richland, WA 99352, USA
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2016 in International Journal of Multiphase Flow
Verified
Journal Article
Closed access
Yucheng FuYucheng Fu
Yucheng Fu
YLYang Liu
Yang Liu

1 August 2019 in Chemical Engineering Science
Verified
Journal Article
Closed access
Yucheng FuYucheng Fu
Yucheng Fu
YLYang Liu
Yang Liu

29 July 2022 in Energy & Environmental Science
Verified
Journal Article
Open access
PDF file
SFShuo Feng
Shuo Feng
RSRajesh Singh
Rajesh Singh
Yucheng FuYucheng Fu
Yucheng Fu
ZLZhuo Li
Zhuo Li
YWYulong Wang
Yulong Wang
Dongping LuDongping Lu
Dongping Lu
Reducing cathode porosity is essential to balancing the electrolyte distribution in lithium–sulfur (Li–S) cells, conserving more pore-filling electrolyte to extend cell cycle life. However, low-porosity electrodes built with nanosized sulfur/carbon (S/C) materials suffer from high tortuosity that significantly deteriorates electrode wetting and hence sulfur utilization. Enabling operation of high-loading sulfur electrodes under both low-porosity and lean-electrolyte conditions is still a challenge and is seldom discussed. In this study, we demonstrated a facile strategy for constructing low-tortuosity through-pores across both vertical and planar directions of electrodes by casting large particles into single-particle-layer electrodes. Through multi-scale characterizations and simulations, correlations between material/electrode structures, electrolyte permeability, polysulfide migration, and sulfur reactions were elucidated. The high-loading and dense sulfur cathode fabricated by this method delivers a high specific capacity (>1000 mA h g−1) at a very low electrolyte/sulfur (E/S) ratio of 4 μL mg−1. This study provides a practical approach to reducing the tortuosity of dense sulfur electrodes by manipulating the porosity distribution, which would be also applicable to improving the rate capability of other high-energy electrodes.

8 June 2018 in Measurement Science and Technology
Verified
Journal Article
Closed access
PDF file
Yucheng FuYucheng Fu
Yucheng Fu
YLYang Liu
Yang Liu
An accurate measurement of bubble shape and size has a significant value in understanding the behavior of bubbles that exist in many engineering applications. Past studies usually use one or two cameras to estimate bubble volume, surface area, among other parameters. The 3D bubble shape and rotation angle are generally not available in these studies. To overcome this challenge and obtain more detailed information of individual bubbles, a 3D imaging system consisting of four high-speed cameras is developed in this paper, and the space carving method is used to reconstruct the 3D bubble shape based on the recorded high-speed images from different view angles. The proposed method can reconstruct the bubble surface with minimal assumptions. A benchmarking test is performed in a 3 cm × 1 cm rectangular channel with stagnant water. The results show that the newly proposed method can measure the bubble volume with an error of less than 2% compared with the syringe reading. The conventional two-camera system has an error around 10%. The one-camera system has an error greater than 25%. The visualization of a 3D bubble rising demonstrates the wall influence on bubble rotation angle and aspect ratio. This also explains the large error that exists in the single camera measurement.

7 September 2023 in Journal of Power Sources
Verified
Journal Article
Open access
WCWenqian Chen
Wenqian Chen
Yucheng FuYucheng Fu
Yucheng Fu
PSPanos Stinis
Panos Stinis

1 December 2016 in Nuclear Engineering and Design
Verified
Journal Article
Closed access
Yucheng FuYucheng Fu
Yucheng Fu
YLYang Liu
Yang Liu