Electroplating processes are widely employed in industrial environments for a large variety of metallic coatings, ranging from technological to decorative applications. Even if the galvanic electrodeposition is certainly a mature technology, new concepts, novel applications, environmental legislation and the new material requirements for next-generation devices make the scientific research in this field still very active. This review focuses mostly at the decorative and wearable applications, and aims to create a bridge between the past knowledge and the future direction that this process, i.e., electrodeposition, is taking. Both the theoretical fundamentals as well as some of the most widespread practical applications—limited to metallic and alloy coatings—are explored. As an integral part of the industrial process, we take a look at the main techniques thought which the quality control of deposits and surfaces is carried out. Finally, global industrial performance and research directions towards sustainable solutions are highlighted.

We focused on preparing cellulose nanofibrils by purification, separation, and mechanical treatment of Kombucha membranes (KM) resulted as secondary product from beverage production by fermentation of tea broth with symbiotic culture of bacteria and yeast (SCOBY). We purified KM using two alkaline solutions, 1 and 4 M NaOH, which afterwards were subjected to various mechanical treatments. Transmission electron microscopy (TEM), scanning electron microscopy (SEM), dynamic light scattering (DLS), X-ray diffraction (XRD), X-ray fluorescence (XRF), Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) were employed to evaluate the purification degree, the size and aspect of cellulose fibrils after each treatment step, the physical-chemical properties of intermediary and final product, and for comparison with micro-crystalline cellulose from wooden sources. We determined that 1 M NaOH solution leads to approx. 85% purification, while a higher concentration assures almost 97% impurities removal. XRD analysis evidenced an increase in crystallinity from 37% to 87% after purification, the characteristic diffractograms of Iα and Iβ cellulose allomorphs, and a further decrease in crystallinity to 46% after microfluidization, fact correlated with a drastically decrease in fibrils’ size. FTIR analysis evidenced the appearance of new chain ends by specific transmission bands at 2941 and 2843cm⁻¹.

Biodegradable blends and nanocomposites were produced from polylactic acid (PLA), poly(3-hydroxybutyrate) (PHB) and cellulose nanocrystals (NC) by a single step reactive blending process using dicumyl peroxide (DCP) as a cross-linking agent. With the aim of gaining more insight into the impact of processing methods upon the morphological, thermal and mechanical properties of these nanocomposites, three different processing techniques were employed: compression molding, extrusion, and 3D printing. The addition of DCP improved interfacial adhesion and the dispersion of NC in nanocomposites as observed by scanning electron microscopy and atomic force microscopy. The carbonyl index calculated from Fourier transform infrared spectroscopy showed increased crystallinity after DCP addition in PLA/PHB and PLA/PHB/NC, also confirmed by differential scanning calorimetry analyses. NC and DCP showed nucleating activity and favored the crystallization of PLA, increasing its crystallinity from 16% in PLA/PHB to 38% in DCP crosslinked blend and to 43% in crosslinked PLA/PHB/NC nanocomposite. The addition of DCP also influenced the melting-recrystallization processes due to the generation of lower molecular weight products with increased mobility. The thermo-mechanical characterization of uncross-linked and cross-linked PLA/PHB blends and nanocomposites showed the influence of the processing technique. Higher storage modulus values were obtained for filaments obtained by extrusion and 3D printed meshes compared to compression molded films. Similarly, the thermogravimetric analysis showed an increase of the onset degradation temperature, even with more than 10 °C for PLA/PHB blends and nanocomposites after extrusion and 3D-printing, compared with compression molding. This study shows that PLA/PHB products with enhanced interfacial adhesion, improved thermal stability, and mechanical properties can be obtained by the right choice of the processing method and conditions using NC and DCP for balancing the properties.

Silver nanoparticles (AgNPs) are considered a promising alternative to the use of antibiotics in fighting multidrug-resistant pathogens. However, their use in medical application is hindered by the public concern regarding the toxicity of metallic nanoparticles. In this study, rationally designed AgNP were produced, in order to balance the antibacterial activity and toxicity. A facile, environmentally friendly synthesis was used for the electrochemical fabrication of AgNPs. Chitosan was employed as the capping agent, both for the stabilization and to improve the biocompatibility. Size, morphology, composition, capping layer, and stability of the synthesized nanoparticles were characterized. The in vitro biocompatibility and antimicrobial activities of AgNPs against common Gram-negative and Gram-positive bacteria were evaluated. The results revealed that chitosan-stabilized AgNPs were nontoxic to normal fibroblasts, even at high concentrations, compared to bare nanoparticles, while significant antibacterial activity was recorded. The silver colloidal dispersion was further mixed with essential oils (EO) to increase the biological activity. Synergistic effects at some AgNP–EO ratios were observed, as demonstrated by the fractionary inhibitory concentration values. Our results reveal that the synergistic action of both polymer-stabilized AgNPs and essential oils could provide a significant efficiency against a large variety of microorganisms, with minimal side effects.

A series of natural sphalerite samples, characterized by an inhomogeneous (zonal) distribution of Fe, Mn, and Cd atoms substituting for Zn, has been investigated by electron probe microanalysis and X-ray element distribution mapping. The cation distributions are markedly inhomogeneous due to the reciprocal effects of the minor elements on their respective solubilities. In particular, zonal partitioning between Fe and Mn and between both cations and Hg was observed in sphalerite, as well as coupled Cu-In and Cu-Fe substitutions. Distinctly different distribution patterns were identified in Mn-free samples with a low Fe-content, as compared to Mn-bearing samples. In the former case, Fe and Cd distribution patterns are very similar, whereas in the latter case, Cd is distributed homogeneously and Mn and Fe patterns are antithetic. The different oscillatory zoning observed in Mn-free samples is attributed to a fast, self-organized solute (Fe, Cd) deposition, although an alternative external origin cannot be ruled out. On the other hand, in the presence of Mn, zoning may be related to an absorption process at the mineral-fluid interface controlled by a competition between Mn and Fe that may explain the observed limited coupled concentration of these elements in sphalerite. The homogeneous distribution of Cd suggests relatively slow crystal growth.