Geometrically accurate and anatomically correct threedimensional geometric models of human bones or bone sections are essential for successful pre-operative planning in orthopedic surgery. For such purposes, 3D polygonal models of bones are usually created based on Computer Tomography (CT) or Magnetic Resonance Imaging (MRI) data. In cases where there is no CT or MRI scan, or part of bone is missing, such three-dimensional polygonal models are difficult to create. In these situations predictive bone models are commonly used. In this paper, the authors describe the developed a software system for creation of Human Bones Customized Polygonal models (HBCP) which is based on the use of the predictive parametric bone model. The software system enables creation of patient-specific polygonal models of bones, by using only a limited number of parameter values. Parameter values can be acquired from volumetric medical imaging methods (CT, MRI), or from two-dimensional imaging methods (i.e. Xray). This paper introduces the new approach to the process of creation of human bones geometrical models which are based on the anatomical landmark points. Testing of the HBCP for the cases of femur bone samples has shown that created bone and bone region models are characterized by a good level of anatomical and morphometric accuracy compared to the results presented in similar researches.

Structural analysis, based on the finite element method, and structural optimization, can help surgery planning or decrease the probability of fixator failure during bone healing. Structural optimization implies the creation of many finite element model instances, usually built using a computer-aided design (CAD) model of the bone-fixator assembly. The three most important features of such CAD models are: parameterization, robustness and bidirectional associativity with finite elements (FE) models. Their significance increases with the increase in the complexity of the modeled fixator. The aim of this study was to define an automated procedure for the configuration and placement of fixators used in the treatment of long bone fractures. Automated and robust positioning of the selfdynamisable internal fixator on the femur was achieved and sensitivity analysis of fixator stress on the change of major design parameters was performed. The application of the proposed methodology is considered to be beneficial in the preparation of CAD models for automated structural optimization procedures used in long bone fixation.

The paper reports on the importance of applying the holistic approach in designing a personalized bone scaffold, but also all other kinds of personalized implants. In addition, the paper attempts to point out the important aspects of the design of a PBS against which the quality of a realistic and applicable design solution should be assessed. The holistic approach refers to the adaptation of design features of a bone scaffold to the multilateral specifics related to the particular patient, its surgical case, and curing treatment. To ensure a successful application, five aspects of personalized bone scaffold design should be considered while it is being adapted: anatomical congruency, mechanical conformity, biochemical compatibility and biodegradability, manufacturability, and implantability. To demonstrate the importance of applying a holistic approach in designing a personalized bone scaffold, the paper shows a case where a patient-specific scaffold aimed at the reconstruction of a large missing piece of mandible was designed. The research resulted in a series of recommendations regarding the methods of bone geometry reconstruction and scaffold design. The paper sheds new light on the desired mechanical properties of a personalized bone scaffold while also recommending possible design parameters for optimizing the construction according to these properties. Finally, it recommends a possible procedure of integral production of personalized bone scaffold and bone graft. The presented so-called holistic approach announces a new systematic process of designing a personalized bone scaffold, which, although requiring a comprehensive consideration of complex requirements, is inevitable to make the designed solution applicable.

Proper fixation techniques are crucial in orthopedic surgery for the treatment of various medical conditions. Fractures of the distal humerus can occur due to either high-energy trauma with skin rupture or low-energy trauma in osteoporotic bone. The recommended surgical approach for treating these extra-articular distal humerus fractures involves performing an open reduction and internal fixation procedure using plate implants. This surgical intervention plays a crucial role in enhancing patient recovery and minimizing soft tissue complications. Dynamic Compression Plates (DCPs) and Locking Compression Plates (LCPs) are commonly used for bone fixation, with LCP extra-articular distal humerus plates being the preferred choice for extra-articular fractures. These fixation systems have anatomically shaped designs that provide angular stability to the bone. However, depending on the shape and position of the bone fracture, additional plate bending may be required during surgery. This can pose challenges such as increased surgery time and the risk of incorrect plate shaping. To enhance the accuracy of plate placement, the study introduces the Method of Anatomical Features (MAF) in conjunction with the Characteristic Product Features methodology (CPF). The utilization of the MAF enables the development of a parametric model for the contact surface between the plate and the humerus. This model is created using specialized Referential Geometrical Entities (RGEs), Constitutive Geometrical Entities (CGEs), and Regions of Interest (ROI) that are specific to the human humerus bone. By utilizing this anatomically tailored contact surface model, the standard plate model can be customized (bent) to precisely conform to the distinct shape of the patient’s humerus bone during the pre-operative planning phase. Alternatively, the newly designed model can be fabricated using a specific manufacturing technology. This approach aims to improve geometrical accuracy of plate fixation, thus optimizing surgical outcomes and patient recovery.