A differential microwave sensor, based on a pair of uncoupled microstrip lines each one loaded with a split ring resonator (SRR), is applied to the measurement of electrolyte concentration in deionized (DI) water. For that purpose, fluidic channels are added on top of the SRR gaps, the most sensitive parts of the structure. The operating principle is based on the measurement of the cross-mode insertion loss, highly sensitive to small asymmetries caused by differences between the reference liquid and the liquid under test (LUT). In this work, the reference liquid is pure DI water (the solvent), whereas the solution, DI water with electrolyte content, is injected to the LUT channel. The proposed sensor is able to detect electrolyte concentrations as small as 0.25 g/L, with maximum sensitivity of 0.033 (g/L)-1. The sensor is validated by measuring the concentration of three types of electrolytes, i.e., NaCl, KCl and CaCl2. Finally, the sensor is applied to monitor variations of total electrolyte concentration in urine samples.

In this paper, a review of the state-of-the-art chipless radiofrequency identification (RFID) technology is carried out. This recent technology may provide low cost tags as long as these tags are not equipped with application specific integrated circuits (ASICs). Nevertheless, chipless-RFID presents a series of technological challenges that have been addressed by different research groups in the last decade. One of these challenges is to increase the data storage capacity of tags, in order to be competitive with optical barcodes, or even with chip-based RFID tags. Thus, the main aim of this paper is to properly clarify the advantages and disadvantages of chipless-RFID technology. Moreover, since the coding information is an important aspect in such technology, the different coding techniques, as well as the main figures of merit used to compare different chipless-RFID tags, will be analyzed.

In this paper, an analytical method to estimate the complex dielectric constant of liquids is presented. The method is based on the measurement of the transmission coefficient in an embedded microstrip line loaded with a complementary split ring resonator (CSRR), which is etched in the ground plane. From this response, the dielectric constant and loss tangent of the liquid under test (LUT) can be extracted, provided that the CSRR is surrounded by such LUT, and the liquid level extends beyond the region where the electromagnetic fields generated by the CSRR are present. For that purpose, a liquid container acting as a pool is added to the structure. The main advantage of this method, which is validated from the measurement of the complex dielectric constant of olive and castor oil, is that reference samples for calibration are not required.

The accurate measurement of the angular displacement and velocity of reaction wheels is necessary for attitude (orientation) control in space vehicles (satellites). In this paper, microwave, contactless, and low-cost (as compared to optical encoders) sensors useful for that purpose are analyzed in detail. The sensor consists of a rotor and a stator. The rotor is a disk (or a circular crown) of dielectric material, where one or several arrays of equidistant single-loop split ring resonators (SRRs) are etched along its edge, forming circular chains of hundreds of SRRs. The stator is a coplanar waveguide (CPW) also loaded with pairs of single-loop SRRs (etched in the back substrate side), with the centers located in the slot region. The sensing principle is based on the amplitude modulation of a harmonic (single-tone continuous wave) feeding signal, achieved when the chains of the rotor are displaced over the SRR pairs of the stator. Both sensor elements (rotor and stator) must be parallel oriented, with the SRR pairs of the CPW in close proximity to the SRR chains of the rotor (and rotated 180°), in order to favor their coupling. By this means, the transmission coefficient of the CPW is varied by the circular motion of the rotor, and significant amplitude modulation of the feeding signal is achieved. From the envelope function, the angular velocity can be accurately determined. With the proposed sensors, instantaneous and practically unlimited rotation speeds can be measured.

This letter is focused on the modeling, analysis, and applications of microstrip lines loaded with pairs of electrically coupled complementary split-ring resonators (CSRRs). Typically, these epsilon-negative (ENG) metamaterial transmission lines are implemented by loading the line with a single CSRR (etched beneath the conductor strip) in the unit cell. This provides a stopband in the vicinity of the CSRR resonance. However, by loading the line with a pair of CSRRs per unit cell, it is possible to either implement a dual-band ENG transmission line (useful, for instance, as a dual-band notch filter), provided the CSRRs are tuned at different frequencies, or to design microwave sensors and comparators based on symmetry disruption (in this case by using identical CSRRs and by truncating symmetry by different means, e.g., asymmetric dielectric loading). The design of these CSRR-based structures requires an accurate circuit model able to describe the line, the resonators, and the different coupling mechanisms (i.e., line-to-resonator and inter-resonator coupling). Thus, a lumped element equivalent circuit is proposed and analyzed in detail. The model is validated by comparison to electromagnetic simulations and measurements. A proof-of-concept of a differential sensor for dielectric characterization is proposed. Finally, the similarities of these structures with coplanar waveguide transmission lines loaded with pairs of SRRs are pointed out.

A high data capacity chipless radio frequency identification (chipless-RFID) system, useful for security and authentication applications, is presented in this paper. Reading is based on the near-field coupling between the tag, a chain of identical split-ring resonators (SRRs) printed on a (typically flexible) dielectric substrate (e.g., liquid crystal polymer, plastic, and paper), and the reader. Encoding is achieved by the presence or absence of SRRs at predefined (equidistant) positions in the chain, and tag identification (ID) is based on sequential bit reading. Namely, the tag must be longitudinally displaced, at short distance, over the reader, a microstrip line loaded with an SRR and fed by a harmonic signal. By this means, the harmonic signal is amplitude modulated, and the (ID) code is contained in the envelope function, which can be obtained by means of an envelope detector. With this system, tag reading requires proximity with the reader, but this is not an issue in many applications within the domain of security and authentication (e.g., secure paper for corporate documents and certificates). Several circularly shaped 40-bit encoders (implemented in a commercial microwave substrate), and the corresponding reader, are designed and fabricated as proof-of-concept demonstrators. Strategies for programming the tags and a first proof-of-concept chipless-RFID tag fabricated on plastic substrate through inkjet printing are included in this paper.