Ionut Sebastian Vintila

Dr. Ionut Sebastian Vintila

Romanian Research and Development Institute for Gas Turbines, Bucharest, Bucureşti, Romania
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 July 2022 in Polymers
Verified
Journal Article
Open access
PDF file
Ionut Sebastian VintilaIonut Sebastian Vintila
Ionut Sebastian Vintila
Jana GhițmanJana Ghițman
Jana Ghițman
Horia  IovuHoria Iovu
Horia Iovu
APAlexandru Paraschiv
Alexandru Paraschiv
Andreia CucuruzAndreia Cucuruz
Andreia Cucuruz
Ionut-Florian PopaIonut-Florian Popa
Ionut-Florian Popa
The paper addresses the synthesis of a nano-fibre network by coaxial electrospinning, embedding the healing agent dicyclopentadiene (DCPD) in polyacrylonitrile (PAN) fibres. Compared to other encapsulation methods, the use of nano-fibres filled with healing agent have no effect on the mechanical properties of the matrix and can address a larger healing area. Additionally, carbon nanotubes were added as nanofillers to enhance the reactivity between DCPD and the epoxydic matrix. The self-healing capability of the nano-fibre network was carried out by flexural tests, at epoxy resin level and composite level. Results obtained from Fourier transform infrared (FTIR) spectrometry, thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) confirmed the successful encapsulation of DCPD healing agent in PAN fibres. Flexural tests indicate that after 48 h, the epoxy resin has recovered 84% of its flexural strength while the composite material recovered 93%.

18 February 2021 in Materials
Verified
Journal Article
Open access
PDF file
Alexandra AdiaconițeiAlexandra Adiaconiței
Alexandra Adiaconiței
Ionut Sebastian VintilaIonut Sebastian Vintila
Ionut Sebastian Vintila
RMRadu Mihalache
Radu Mihalache
APAlexandru Paraschiv
Alexandru Paraschiv
FTFrigioescu Tiberius-Florian
Frigioescu Tiberius-Florian
LPLaurent Pambaguian
Laurent Pambaguian
The efficiency of a centrifugal pump for mechanical pump fluid loops, apart from the design, relies on the performance of the closed impeller which is linked to the manufacturing process in terms of dimensional accuracy and the surface quality. Therefore, the activities of this paper were focused on defining the manufacturing process of a closed impeller using the additive manufacturing technology for mechanically pumped fluid loop (MPFL) systems in space applications. Different building orientations were studied to fabricate three closed impellers using selective laser melting technology and were subjected to dimensional accuracy and surface quality evaluations in order to identify the optimal building orientation. The material used for the closed impeller is Inconel 625. The results showed that both geometrical stability and roughness were improved as the building orientation increased, however, the blade thickness presented small deviations, close to imposed values. Finishing processes for inaccessible areas presented significant results in terms of roughness, nevertheless, the process can be further improved. Abrasive flow machining (AFM) post-processing operations have been considered and the results show major improvements in surface quality. Thus, important steps were made towards the development of complex structural components, consequently increasing the technological readiness level of the additive manufacturing process for space applications.

4 May 2020 in Polymers
Verified
Journal Article
Open access
PDF file
Ionut Sebastian VintilaIonut Sebastian Vintila
Ionut Sebastian Vintila
Horia  IovuHoria Iovu
Horia Iovu
AAAndreea Alcea
Andreea Alcea
Andreia CucuruzAndreia Cucuruz
Andreia Cucuruz
AMAndrei Cristian Mandoc
Andrei Cristian Mandoc
Bogdan Stefan VasileBogdan Stefan Vasile
Bogdan Stefan Vasile
The activities of this paper were focused on an in-situ fabrication process for producing two self-healing systems containing dicyclopentadiene and 5-ethylidene-2-norbornene monomers encapsulated in a urea-formaldehyde shell and integration methods applied in the epoxy matrix to analyse and compare the influences of their integration into the neat epoxy matrix. The self-healing systems were first synthesized according to a literature review, and subsequently, an optimization process was conducted for the fabrication process. Neat epoxy specimens were fabricated as reference specimens and subjected to flexural tests. Several integration methods for incorporating the self-healing systems into the epoxy resin were investigated. The optimal method presenting the best dispersion of the healing system was achieved by reducing the viscosity of the epoxy matrix with 10 vol % acetone solution, the addition of a microcapsule in the matrix, and homogenization at 60 °C at 100 rpm. Thermal analysis was performed in order to observe the mass loss obtained with an increasing temperature and phase changes for both poly-urea-formaldehyde (PUF)-dicyclopentadiene (DCPD) and melamine-urea-formaldehyde (MUF)-5-ethylidene-2-norbornene (ENB) systems. The thermogravimetric analysis performed for the PUF-DCPD system indicates a total loss of mass in the range of 30–500 °C of 72.604% and for the MUF-ENB system, indicates a total mass loss in the range of 30–500 °C of 74.093%. Three-point bending tests showed higher mechanical properties for PUF-DCPD (80%) than MUF-ENB (40%) compared to the neat epoxy systems. Numerical simulations were performed to obtain a better understanding of the microcapsule behavior when embedded in an epoxy matrix.

9 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
Alexandra AdiaconițeiAlexandra Adiaconiței
Alexandra Adiaconiței
Ionut Sebastian VintilaIonut Sebastian Vintila
Ionut Sebastian Vintila
RMRadu Mihalache
Radu Mihalache
APAlexandru Paraschiv
Alexandru Paraschiv
FTFrigioescu Tiberius-Florian
Frigioescu Tiberius-Florian
LPLaurent Pambaguian
Laurent Pambaguian
In the space industry, the market demand for high-pressure mechanically pumped fluid loop (MPFL) systems has increased the interest for integrating advanced technologies in the manufacturing process of critical components with complex geometries. The conventional manufacturing process of a closed impeller encounters different technical challenges, but using additive manufacturing (AM) technology, the small component is printed, fulfilling the quality requirements. This paper presents the Laser Powder Bed Fusion (LPBF) process of a closed impeller designed for a centrifugal pump integrated in an MPFL system with the objective of defining a complete manufacturing process. A set of three closed impellers was manufactured, and each closed impeller was subjected to dimensional accuracy analysis, before and after applying an iterative finishing process for the internal surface area. One of the impellers was validated through non-destructive testing (NDT) activities, and finally, a preliminary balancing was performed for the G2.5 class. The process setup (building orientation and support structure) defined in the current study for a pre-existing geometry of the closed impeller takes full advantages of LPBF technology and represents an important step in the development of complex structural components, increasing the technological readiness level of the AM process for space applications.

30 March 2018 in Materiale Plastice
Verified
Journal Article
Closed access
MCMihaela Raluca Condruz
Mihaela Raluca Condruz
CPCristian Puscasu
Cristian Puscasu
LVLucia Raluca Voicu
Lucia Raluca Voicu
Ionut Sebastian VintilaIonut Sebastian Vintila
Ionut Sebastian Vintila
APAlexandru Paraschiv
Alexandru Paraschiv
DMDragos Alexandru Mirea
Dragos Alexandru Mirea
Mihaela Raluca Condruz, Cristian Puscasu, Lucia Raluca Voicu, Ionut Sebastian Vintila, Alexandru Paraschiv, Dragos Alexandru Mirea - Fiber Reinforced Composite Materials for Proton Radiation Shielding

16 October 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Ionut-Florian PopaIonut-Florian Popa
Ionut-Florian Popa
CDCristian Dobromirescu
Cristian Dobromirescu
Ionut Sebastian VintilaIonut Sebastian Vintila
Ionut Sebastian Vintila
ITIulia Tinca
Iulia Tinca
DMDragos Mihai
Dragos Mihai
DCDaniel Crunteanu
Daniel Crunteanu
The current paper addresses the challenges in manufacturing a critical component of a centrifugal pump for space active thermal control systems of satellites, namely, the closed centrifugal impeller. Compared to the classical technologies, there is an obvious advantage of additive manufacturing of closed impellers, due to the possibility of creating complex geometries, which boost the hydraulic performances of the part and, implicitly, of the pump. In this regard, the authors performed a comparative analysis between a closed impeller obtained by classical machining and three manufactured by additive technology (selective laser melting) by means of dimensional inspection, non-destructive testing, and experimental evaluation. The study performed here showed that the additively manufactured closed impellers exhibited similar hydraulic performances to the classical one, without the need for performing post-processing of internal surfaces. Also, in terms of dimensional and geometrical stability, the additively manufactured closed impellers were within the imposed tolerances, demonstrating the feasibility of obtaining such complex parts by using additive manufacturing. Subsequently, the allocated time for manufacturing decreased by 75% for the closed impellers manufactured by additive technologies, and the need for using four technological processes was decreased to only two, printing and post-processing.