This paper presents a numerical investigation of the scour phenomenon around a submarine pipeline. The numerical simulations are performed using SedFoam, a two-phase flow model for sediment transport implemented in the open source Computational Fluid Dynamics (CFD) toolbox OpenFOAM. The paper focuses on the sensitivity of the granular stress model and the turbulence model with respect to the predictive capability of the two-phase flow model. The quality of the simulation results is estimated using a statistical estimator: the Brier Skill Score. The numerical results show no sensitivity to the granular stress model. However, the results strongly depend on the choice of the turbulence model, especially through the different implementations of the cross-diffusion term in the dissipation equation between the and the 2006 models. The influence of the cross-diffusion term tends to indicate that the sediment transport layer behaves more as a shear layer than as a boundary layer, for which the model is more suitable.
In this paper the capabilities of the turbulence-resolving Eulerian–Eulerian two-phase flow model to predict the suspension of mono-dispersed finite-sized solid particles in a boundary layer flow are investigated. For heavier-than-fluid particles, having settling velocity of the order of the bed friction velocity, the two-fluid model significantly under-estimates the turbulent dispersion of particles. It is hypothesized that finite-size effects are important and a correction model for the drag law is proposed. This model is based on the assumption that the turbulent flow scales larger than the particle diameter will contribute to the resolved relative velocity between the two phases, whereas eddies smaller than the particle diameter will have two effects: (i) they will reduce the particle response time by adding a sub-particle scale eddy viscosity to the drag coefficient, and (ii) they will contribute to increase the production of granular temperature. Integrating finite-size effects allows us to quantitatively predict the concentration profile for heavier-than-fluid particles without any tuning parameter. The proposed modification of the two-fluid model extends its range of applicability to tackle particles having a size belonging to the inertial range of turbulence and allows us to envision more complex applications in terms of flow forcing conditions, i.e. sheet flow, wave-driven transport, turbidity currents and/or flow geometries, i.e. ripples, dunes, scour.
In this paper, two-phase flow simulations of oscillatory sheet flow experimental configurations involving medium and fine sand using a turbulence-resolving two-fluid model are presented. The turbulence-resolving two-phase flow model reproduces the differences of behaviour observed between medium and fine sand whereas turbulence-averaged models require an almost systematic tuning of empirical model coefficients for turbulence–particle interactions. The two-fluid model explicitly resolves these interactions and can be used to study in detail the differences observed experimentally. Detailed analysis of concentration profiles, flow hydrodynamics, turbulent statistics and vertical mass balance allowed the confirmation that unsteady effects, namely phase-lag effect and enhanced boundary layer thickness, for fine sand are not only due to the small settling velocity of the particles relative to the wave period. The occurrence and intensity of unsteady effects are also affected by a complex interplay between flow instabilities, strong solid-phase Reynolds stress and turbulence attenuation caused by the presence of the particles.
In this paper, an Eulerian two-phase flow model, sedFoam, is extended to include an air phase together with its water and sediment phases. The numerical model called sedInterFoam is implemented using the open-source library OpenFOAM. sedInterFoam includes the previous features of sedFoam for sediment transport modeling and also solves the air–water interface using the volume-of-fluid method coupled with the waves2Foam toolbox for free-surface wave generation and absorption. Using sedInterFoam, four test cases are successfully reproduced to validate the free-surface evolution algorithm's implementation, mass conservation of sediment and fluid phases, and predictive capabilities and to demonstrate its potential in modeling a broader range of coastal applications with sediment transport dominated by surface waves.
In this paper, the application of a two-phase flow model to scour processes is presented. The model is first calibrated against experimental data of unidirectional sheet-flow (one-dimensional configuration). The model is then applied to multi-dimensional configurations for the scour under a submarine pipeline and around a vertical pile. The results show that quantitative results can be obtained at the upstream sides of structures, the lee-wake erosion driven by the vortex shedding deserves further research.
The height of the atmospheric boundary layer (ABL) exerts a significant influence on flow behavior within wind farms and directly impacts their performance. This study investigates how variations in ABL height and capping inversion layer thickness affect the efficiency and power output of a gigawatt-scale wind farm. Five advanced numerical approaches, ranging from high-fidelity large-eddy simulations (LESs) to Reynolds-averaged Navier–Stokes (RANS), are used to model farm-scale flow dynamics under shallow (∼150 m) and deep (∼500 m) ABL conditions. The results consistently show that shallow ABLs increase flow blockage and turbine wake interactions, leading to reduced power production. In contrast, deeper ABLs promote enhanced wake recovery and increased overall energy yield. These trends were observed across all solvers, demonstrating the robustness of the findings. Notably, while some quantitative differences emerged depending on modeling fidelity and computational domain size, the overarching trends remained consistent among the participating research institutions and industry partners. The simulation cases performed are complex, and the results of the different methods show a variation of up to 10 %, and further research is needed to limit this gap. Based on these results, it is not clear to what extent the variation depends on the fidelity level of the models used. The study concludes that ABL height and stability are critical parameters to consider in wind energy siting and turbine layout design to optimize performance across varying atmospheric conditions.