To solve the issues of insufficient early strength of cement stabilized soil and high resource cost, high reduction cost, and high environmental cost induced by the application of cement, the slag and fly ash-based geopolymer was adopted as the stabilizer to treat riverside soft soil. This study mainly investigated the effects of stabilizer content, slag-to-fly ash ratio, and alkaline activator content on the strength of geopolymer stabilized soils with different curing ages. Unconfined compressive strength (UCS), scanning electron microscope (SEM), and X-ray energy spectrum analysis (EDS) tests were carried out. The results show that the stabilizer content, slag–fly ash ratio, and alkaline activator content have a decisive influence on the UCS of geopolymer-stabilized soil. The mix-proportions scheme of geopolymer stabilized riverside soft soil, with a geopolymer content of 15%, a slag–fly ash ratio of 80:20, and an alkaline activator content of 30%, is considered optimum. It is proven by SEM that the uniformly distributed gelatinous products formed in the geopolymer-stabilized soil bind the soil particles tightly. Moreover, the EDS analysis confirms that the gelatinous products are mainly composed of C-S-H gel and sodium-based aluminosilicate (N-A-S-H).

Geopolymer, as a new type of solid waste-based inorganic cementitious material, exhibits outstanding behavior in terms of physical and chemical performance, macromechanical properties, long-lasting stability, and features potential application development tendency in the field of repair and reinforcement of existing concrete structures. This paper investigated the interfacial behavior of geopolymer mortar with OPC concrete substrate under different slag, fly ash and red mud mixing proportions, while cement mortar was used as a control group for the research. The interfacial bonding properties of the geopolymer mortar to the OPC concrete substrate were elaborated by carrying out split tensile test, double-sided shear test, and three-point bending test. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were employed to further analyze the microstructural characteristics and physical phase components of the interfacial transition zone between the geopolymer mortar and the OPC concrete substrate. The results indicated that the compressive strength of slag-fly ash-red mud-based geopolymer mortar under different mixing ratio conditions was consistently superior to that of cement mortar, where the optimum mixing ratio for the geopolymer mortar was S33F33R33. Overall, the interfacial bonding properties of the geopolymer mortar to the OPC concrete substrate gradually increased with the increment of the slag content, however, an evolutionary trend of minor enhancement followed by a gradual reduction was observed with the growth of the fly ash and red mud content.

The complexity of composite geopolymer materials results in instability in the setting and hardening of geopolymer-stabilized soil. In order to determine the appropriate mix proportion scheme for composite geopolymer-stabilized soil, this study investigated the effects of two preparation methods, fly ash/slag ratio and alkali activator modulus, on workability and strength development trends in alkali-excited fly ash and slag-based geopolymer-stabilized soil. The results showed that the high ambient temperatures created by the one-step method were more conducive to the setting and hardening of the geopolymer-stabilized soil; its 3 d/28 d UCS (unconfined compression strength) ratio was 62.43–78.60%, and its 7 d/28 d UCS ratio was 70.37–83.63%. With increases of the alkali activator modulus or the proportion of fly ash, the setting time of stabilized soil was gradually prolonged, and its fluidity increased. Meanwhile, the strength development of stabilized soil was significantly affected by the proportion of fly ash and the alkali activator modulus; the maximum UCS value was obtained at II-2-O, prepared by the one-step method, with an alkali activator modulus of 1.2 and a fly ash/slag ratio of 20/80. Specifically, the 3, 7, and 28 d UCS values of II-2-O were 1.65, 1.89, and 2.26 MPa, respectively, and its 3 d/28 d UCS ratio and 7 d/28 d UCS ratio were 73.01% and 83.63%, respectively. These results will be of great importance in further research on (and construction guidance of) composite geopolymer-stabilized soil.

The compaction density of sand-gravel materials has a strong gradation correlation, mainly affected by some material source parameters such as P5 content (material proportion with particle size greater than 5 mm), maximum particle size and curvature coefficient. When evaluating the compaction density of sand-gravel materials, the existing compaction density evaluation models have poor robustness and adaptability because they do not take into full consideration the impact of material source parameters. To overcome the shortcomings of existing compaction density models, this study comprehensively considers the impact of material source parameters and compaction parameters on compaction density. Firstly, asymmetric data were fused and a multi-source heterogeneous dataset was established for compaction density analysis. Then, the Elman neural network optimized by the adaptive simulated annealing particle swarm optimization algorithm was proposed to establish the compaction density evaluation model. Finally, a case study of the Dashimen water conservancy project in China is employed to demonstrate the effectiveness and feasibility of the proposed method. The results show that this model performs high-precision evaluation of the compaction density at any position of the entire working area which can timely correct the weak area of compaction density on the spot, and reduce the number of test pit tests.

The rapid advancement of information technologies, such as cloud computing, internet of things (IoT), and big data, has significantly enhanced the intelligence level in dam construction. Intelligent monitoring systems for dam filling have garnered considerable attention from water conservancy and hydropower engineering units, owing to their capability for refined management and quality control of layered and compartmentalized construction processes. The construction of earth–rock dams has undergone a transformation, shifting from manual management of dam compaction equipment, layer management, and quality control to a comprehensive intelligent approach. This new approach encompasses finegrained control of unit engineering, dam material identification, unmanned driving technology, real-time assessment and monitoring of compaction quality, and early warning forecasting. This article presents a systematic overview of key technologies employed in the intelligent construction process of earth–rock dams. These technologies include the fine decomposition of building information modeling (BIM) models on web platforms, rapid identification of dam material particle size, the application of autonomous driving technology for intelligent dam filling, and real-time monitoring and evaluation of dam compaction characteristics. Additionally, the paper discusses the latest research results in the field, building upon existing technology progress, and concludes by exploring the future development trends of intelligent dam construction. The construction of intelligent earth–rock dams serve as a crucial reference and valuable lessons for the development and construction of high earth–rock dam projects.

Geopolymer, as a new type of solid waste-based inorganic cementitious material, exhibits outstanding Behavior in terms of physical and chemical performance, macro-mechanical properties and long-lasting stability, and features potential application development tendency in the field of repair and reinforcement of existing concrete structures. This paper investigates the interfacial Behavior of geopolymer mortar with OPC concrete substrate under different slag, fly ash and red mud mixing proportions, while cement mortar was used as a control group for the research. The interfacial bonding properties of the geopolymer mortar to the OPC concrete substrate were elaborated by carrying out split tensile test, two-sided shear test and three-point bending test. The scanning electron microscopy (SEM) and X-ray diffraction (XRD) were employed to further analyse the microstructural characteristics and physical phase components of the interfacial transition zone between the geopolymer mortar and the OPC concrete substrate. The results indicated that the compressive strength of slag-fly ash-red mud-based geopolymer mortar under different mixing ratio conditions was consistently superior to that of cement mortar. Overall, the interfacial bonding properties of the geopolymer mortar to the OPC concrete substrate gradually increased with the increment of the slag content, however, an evolutionary trend of minor enhancement followed by a gradual reduction was observed with the growth of the fly ash and red mud content.