Herein, N,P-rich carbon/carbon/Co2P2O7 hollow nanotubes with a multilayered wall structure were successfully fabricated for the ORR electrocatalyst. The hollow tube structure catalysts were obtained by carbonizing Co2P2O7/C coated with the phytate-doped PANI. The Co2P2O7/C was obtained by phosphorylating a basic cobalt carbonate with phytic acid (PA). Onset and positive half-wave potentials were measured at 0.90 and 0.84 V, respectively, with a diffusion-limited current density of 4.58 mA/cm2. Effect of the thickness of polyaniline (PANI) in the electrocatalyst precursor was also investigated. The specific surface area as well as the content of graphitic N altered as the time of PANI polymerization increased, resulting in remarkably different catalytic activities. This study of hollow nanotube catalysts exhibits efficient noble-metal-free oxygen reduction reaction electrocatalysts for other chemical systems, which will provide abundant electrochemical active centers and sufficient energy.
The diffusion coatings were deposited on commercially pure Ti and Ti-6Al-4V alloy at up to 1000 °C for up to 10 h using the pack cementation method. The pack powders consisted of 4 wt% Al (Al reservoir) and 4 wt% NH4Cl (activator) which were balanced with Al2O3 (inert filler). The growth kinetics of coatings were gravimetrically measured by a high precision balance. The aluminised specimens were characterised by means of scanning electron microscopy (SEM), energy dispersive spectrometer (EDS) and X-ray diffraction (XRD). At the early stages of deposition, a TiO2 (rutile) scale, other than aluminide coating, was developed on both materials at <900 °C. As the experimental temperature arose above 900 °C, the rutile layer became unstable and reduced to the low oxidation state of Ti oxides. When the temperature increased to 1000 °C, the TiO2 scale dissociated almost completely and the aluminide coating began to develop. After a triple-layered coating was generated, the coating growth was governed by the outward migration of Ti species from the substrates and obeyed the parabolic law. The coating formed consisted of an outer layer of Al3Ti, a mid-layer of Al2Ti and an inner layer of AlTi. The outer layer of Al3Ti dominated the thickness of the aluminide coating.
In the present work, four groups of spherical chromium carbide reinforced NiCrBSi hardmetal coatings were prepared on AISI 4145 steel by plasma transferred arc (PTA) technique. The corrosion behavior of the four as-received hardmetal coatings in 0.5 mol/L H2SO4 solution was investigated by polarization curve and electrochemical impedance spectroscopy (EIS). The results revealed that more Cr-rich carbides (Cr3C2, Cr7C3 and M23(C, B)6) are formed in the chromium carbide reinforced coatings, while for the NiCrBSi hardmetal coating only Cr7C3 carbide was detected by XRD. The polarization results show that the chromium carbide reinforced NiCrBSi hardmetal coatings have positive corrosion potential and lower corrosion current, providing a better protective effect to the substrate metal. The combined effects of Cr-rich carbide ceramic phases and a more stable passive film of Cr2O3 greatly improved the corrosion resistances of the chromium carbide reinforced NiCrBSi hardmetal coatings. The coating with the highest spherical chromium carbide addition has more pores because of the thermal stress due to the difference of thermal expansion coefficient between the NiCrBSi bonding phase and chromium carbide reinforced phase. The negative effects of the pores weaken the corrosion resistance, and the coating with the 30% chromium carbide content shows the best corrosion resistance. For NiCrBSi hardmetal coatings with higher reinforced chromium carbide content, the repeatability of the corrosion current obtained by polarization fitting is not as good as that of coatings with lower chromium carbide content. The repeatability of polarization results becomes worse when the specimens keep in a more stable passive state.