Tomasz Sterzynski

Prof. Tomasz Sterzynski

Poznan University of Technology
orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 November 2004 in Polymer International
Verified
Journal Article
Closed access
PDF file
ARAnna Romankiewicz
Anna Romankiewicz
Tomasz SterzynskiTomasz Sterzynski
Tomasz Sterzynski
WBWitold Brostow
Witold Brostow

10 December 2021 in Polymers
Verified
Journal Article
Open access
PDF file
JTJolanta Tomaszewska
Jolanta Tomaszewska
Tomasz SterzynskiTomasz Sterzynski
Tomasz Sterzynski
AWAneta Wozniak-Braszak
Aneta Wozniak-Braszak
MBMichal Banaszak
Michal Banaszak
This review addresses the impact of different nanoadditives on the glass transition temperature (Tg) of polyvinyl chloride (PVC), which is a widely used industrial polymer. The relatively high Tg limits its temperature-dependent applications. The objective of the review is to present the state-of-the-art knowledge on the influence of nanofillers of various origins and dimensions on the Tg of the PVC. The Tg variations induced by added nanofillers can be probed mostly by such experimental techniques as thermomechanical analysis (TMA), dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and dielectric thermal analysis (DETA). The increase in Tg is commonly associated with the use of mineral and carbonaceous nanofillers. In this case, a rise in the concentration of nanoadditives leads to an increase in the Tg due to a restraint of the PVC macromolecular chain’s mobility. The lowering of Tg may be attributed to the well-known plasticizing effect, which is a consequence of the incorporation of oligomeric silsesquioxanes to the polymeric matrix. It has been well established that the variation in the Tg value depends also on the chemical modification of nanofillers and their incorporation into the PVC matrix. This review may be an inspiration for further investigation of nanofillers’ effect on the PVC glass transition temperature.

12 June 2020 in Materials
Verified
Journal Article
Open access
PDF file
MMMateusz Mucha
Mateusz Mucha
AKAneta Krzyzak
Aneta Krzyzak
EKEwelina Kosicka
Ewelina Kosicka
Emerson CoyEmerson Coy
Emerson Coy
MKMikołaj Kościński
Mikołaj Kościński
MSMichał Sałaciński
Michał Sałaciński
The aim of the study is to assess the effect of multi-walled carbon nanotubes (MWCNTs) on the wear behavior of MWCNT-doped epoxy resin. In this study, a laminating resin system designed to meet the standards for motor planes was modified with MWCNTs at mass fractions from 0.0 wt.% to 2.0 wt.%. The properties of the carbon nanotubes were determined in Raman spectroscopy and HR-TEM. An examination of wear behavior was conducted on a linear abraser with a visual inspection on an optical microscope and SEM imaging, mass loss measurement, and evaluation of the wear volume on a profilometer. Moreover, the mechanical properties of MWCNTs/epoxy nanocomposite were evaluated through a tensile test and Shore D hardness test. The study shows that the best wear resistance is achieved for the mass percentage between 0.25 wt.% and 0.5 wt.%. For the same range, the tensile strength reaches the highest values and the hardness the lowest values. Together with surface imaging and a topography analysis, this allowed describing the wear behavior in the friction node and the importance of the properties of the epoxy nanocomposite.

25 June 2016 in Materials
Verified
Journal Article
Open access
PDF file
Beata StrzemieckaBeata Strzemiecka
Beata Strzemiecka
Łukasz KlapiszewskiŁukasz Klapiszewski
Łukasz Klapiszewski
AJArtur Jamrozik
Artur Jamrozik
TSTadeusz J. Szalaty
Tadeusz J. Szalaty
Danuta MatykiewiczDanuta Matykiewicz
Danuta Matykiewicz
Teofil JesionowskiTeofil Jesionowski
Teofil Jesionowski
Functional lignin–SiO2 hybrid fillers were prepared for potential application in binders for phenolic resins, and their chemical structure was characterized. The properties of these fillers and of composites obtained from them with phenolic resin were compared with those of systems with lignin or silica alone. The chemical structure of the materials was investigated by Fourier transform infrared spectroscopy (FT-IR) and carbon-13 nuclear magnetic resonance spectroscopy (13C CP MAS NMR). The thermal stability of the new functional fillers was examined by thermogravimetric analysis–mass spectrometry (TG-MS). Thermo-mechanical properties of the lignin–silica hybrids and resin systems were investigated by dynamic mechanical thermal analysis (DMTA). The DMTA results showed that abrasive composites with lignin–SiO2 fillers have better thermo-mechanical properties than systems with silica alone. Thus, fillers based on lignin might provide new, promising properties for the abrasive industry, combining the good properties of lignin as a plasticizer and of silica as a filler improving mechanical properties.

1 February 2004 in Polymer Engineering & Science
Verified
Journal Article
Closed access
PDF file
Tomasz SterzynskiTomasz Sterzynski
Tomasz Sterzynski
HØHarry Øysæd
Harry Øysæd