Jolanta Tomaszewska

Dr. Jolanta Tomaszewska

UTP University of Science and Technology in Bydgoszcz
orcid

Research Focus & Metrics

Academic Career Length

28Years (1999-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2020 in Journal of Molecular Liquids
Verified
Journal Article
Closed access
NDNazarii Danyliuk
Nazarii Danyliuk
JTJolanta Tomaszewska
Jolanta Tomaszewska
TTTetiana Tatarchuk
Tetiana Tatarchuk

6 May 2020 in Environmental Science and Pollution Research
Verified
Journal Article
Closed access
PDF file
TTTetiana Tatarchuk
Tetiana Tatarchuk
Mu. NaushadMu. Naushad
Mu. Naushad
JTJolanta Tomaszewska
Jolanta Tomaszewska
PKPrzemysław Kosobucki
Przemysław Kosobucki
MMMariana Myslin
Mariana Myslin
PŚPiotr Ścigalski
Piotr Ścigalski

10 December 2021 in Polymers
Verified
Journal Article
Open access
PDF file
JTJolanta Tomaszewska
Jolanta Tomaszewska
Tomasz SterzynskiTomasz Sterzynski
Tomasz Sterzynski
AWAneta Wozniak-Braszak
Aneta Wozniak-Braszak
MBMichal Banaszak
Michal Banaszak
This review addresses the impact of different nanoadditives on the glass transition temperature (Tg) of polyvinyl chloride (PVC), which is a widely used industrial polymer. The relatively high Tg limits its temperature-dependent applications. The objective of the review is to present the state-of-the-art knowledge on the influence of nanofillers of various origins and dimensions on the Tg of the PVC. The Tg variations induced by added nanofillers can be probed mostly by such experimental techniques as thermomechanical analysis (TMA), dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and dielectric thermal analysis (DETA). The increase in Tg is commonly associated with the use of mineral and carbonaceous nanofillers. In this case, a rise in the concentration of nanoadditives leads to an increase in the Tg due to a restraint of the PVC macromolecular chain’s mobility. The lowering of Tg may be attributed to the well-known plasticizing effect, which is a consequence of the incorporation of oligomeric silsesquioxanes to the polymeric matrix. It has been well established that the variation in the Tg value depends also on the chemical modification of nanofillers and their incorporation into the PVC matrix. This review may be an inspiration for further investigation of nanofillers’ effect on the PVC glass transition temperature.

15 September 2015 in Polymers
Verified
Journal Article
Open access
PDF file
Łukasz KlapiszewskiŁukasz Klapiszewski
Łukasz Klapiszewski
FPFranciszek Pawlak
Franciszek Pawlak
JTJolanta Tomaszewska
Jolanta Tomaszewska
Teofil JesionowskiTeofil Jesionowski
Teofil Jesionowski
An advanced SiO2–lignin hybrid material was obtained and tested as a novel poly(vinyl chloride) (PVC) filler. The processing of compounds of poly(vinyl chloride) in the form of a dry blend with silica–lignin hybrid material and, separately, with the two components from which that material was prepared, was performed in a Brabender mixing chamber. An analysis was made of processing (mass melt flow rate, MFR), thermal (thermogravimetric analysis, Congo red and Vicat softening temperature test) and tensile properties of the final PVC composites with fillers in a range of concentrations between 2.5 wt % and 10 wt %. Additionally, the effects of filler content on the fusion characteristics of PVC composites were investigated. The homogeneity of dispersion of the silica–lignin hybrid material in the PVC matrix was determined by optical microscopy and SEM. Finally, it should be noted that it is possible to obtain a PVC composite containing up to 10 wt % of silica–lignin filler using a melt processing method. The introduction of hybrid filler into the PVC matrix results in a homogeneous structure of the composites and positive processing and functional properties, especially thermal stability and Vicat softening temperature.

1 September 2015 in Composites Science and Technology
Verified
Journal Article
Closed access
TSTomasz Sterzyński
Tomasz Sterzyński
JTJolanta Tomaszewska
Jolanta Tomaszewska
Jacek AndrzejewskiJacek Andrzejewski
Jacek Andrzejewski
KSKatarzyna Skórczewska
Katarzyna Skórczewska

30 June 2017 in Polymers
Verified
Journal Article
Open access
PDF file
Łukasz KlapiszewskiŁukasz Klapiszewski
Łukasz Klapiszewski
JTJolanta Tomaszewska
Jolanta Tomaszewska
KSKatarzyna Skórczewska
Katarzyna Skórczewska
Teofil JesionowskiTeofil Jesionowski
Teofil Jesionowski
A functional magnesium hydroxide/lignin hybrid system was prepared by grinding and mixing the pure precursors using a planetary ball mill. In addition, the thermal stability was assessed based on the total mass loss of the hybrid system within the temperature range of 30–1000 °C, which amounted to 38%. Moreover, the average particle size was at 4.9 μm as determined by the laser diffraction method. The effect of addition of the prepared and characterized Mg(OH)2/lignin hybrid filler at concentrations ranging from 2.5 wt % to 10 wt % on the processing as well as mechanical and thermal properties of composites on the matrix of the unplasticized PVC compound was also evaluated. The addition of a filler to the poly(vinyl chloride) matrix causes a significant improvement of its thermal stability, which is approximately three times higher compared to a polymer without a filler. Furthermore, the prepared composites are additionally characterized by advantageous mechanical properties, especially higher Young’s modulus. A 10% increase in the oxygen index of PVC composites upon addition of 10 wt % hybrid fillers has also been observed, which contributes to an extended range of their application under conditions that require notable fire resistance.