Machining of shafts characterized by a high compliance is difficult due to the occurrence of self-excited chatter vibrations. It is possible to limit their occurrence through the appropriate selection of technological parameters. For a proper selection of these parameters it is necessary to know the dynamic properties of the machine–tool–workpiece. This study proposes an approach through which these properties can be determined as a result of the synthesis of the dynamic properties of the system, using the receptance coupling method. Knowledge of these properties allows us to select the technological parameters of the lathe using the assistance system integrated into the CNC (Computerized Numerical Control). The final section of this work presents the experimental validation of the assistant and proposed procedures.

Modern technology allows ductile cast iron parts to be efficiently machined while ensuring a relatively long tool life. One of the basic indices describing the susceptibility of ductile cast irons to change in volume, shape, and dimensions under machining conditions is their machinability. Machinability can be expressed directly in terms of the values of basic quantities such as periodic cutting speed and roughness. At the same time, machinability is a relative quantity evaluated alternatively. This means that the machinability of ductile cast iron can be good, allowing high cutting speeds to be achieved, but it can also be poor, expressed in terms of poor surface quality. In the experimental research carried out, an attempt was made to determine the limit values of the cutting speed, beyond which one should not exceed, in order to increase the efficiency of the machining process. The surface roughness, unlike the periodic cutting speed, is a quantity defined in the product design documentation, so its limits must be observed. In addition to the usual indices of surface geometric texture, the research analysed alternative indices for determining the condition of surface geometric texture and the influence of periodic cutting speed on their values. In the conclusions, valuable recommendations are given for designers and technologists on the purpose and functionality of product surfaces and how to define them. Methods of specifying tribological characteristics, hydrophobic or hydrophilic properties, as well as the ability to retain fluids and maintain protective coatings of ductile cast iron parts after machining are described, for which relative values, depending on the machining parameters used, can vary from about 10 to even 30%.

In order to ensure machining stability, it is essential to properly determine the dynamic properties of machine tool–workpiece system. Experimental modal analysis provides good results; however, due to high time consumption, in some cases, its use is not practically justified. Then, a receptance coupling method can be used, that allows for the synthesis of the experimental models of the machine tool components and analytical models of the workpiece. However, a significant disadvantage of this method is the need for the experimental identification of the rotational degrees-of-freedom, fully defining dynamic properties of the spindle. This paper presents an improved method based on inverse receptance coupling, which enables effective identification of the spindle dynamics with the properties of the joint. Then, a measurement procedure and results of the experimental validation are presented.

This paper presents an issue of machining stability prediction of dynamic “lathe – workpiece” system evaluated using receptance coupling method. Dynamic properties of the lathe components (the spindle and the tailstock) are assumed to be constant and can be determined experimentally based on the results of the impact test. Hence, the variable of the system “machine tool – holder – workpiece” is the machined part, which can be easily modelled analytically. The method of receptance coupling enables a synthesis of experimental (spindle, tailstock) and analytical (machined part) models, so impact testing of the entire system becomes unnecessary. The paper presents methodology of analytical and experimental models synthesis, evaluation of the stability lobes and experimental validation procedure involving both the determination of the dynamic properties of the system and cutting tests. In the summary the experimental verification results would be presented and discussed.

The paper presents the concept of a support system for the manufacture of machine spare parts. The operation of the system is based on a reverse engineering module enabling feature recognition based on a 3D parts scan. Then, a CAD geometrical model is generated, on the basis of which a machining strategy using the CAM system is developed. In parallel, based on the geometric model, a finite element model is built, which facilitates defining technological parameters, allowing one to minimize the risk of vibrations during machining. These parameters constitute input information to the CAM module. The operation of the described system is presented on the example of machining parts of the shaft class. The result is a replacement part, the accuracy of which was compared by means of the iterative closest point algorithm obtaining the RMSE at the level of scanner accuracy.