Three-dimensional numerical simulations are performed to evaluate the effect of porous baffles on the efficiency of water treatment contact tanks. A second-order accurate numerical model is employed for the solutions of unsteady flow and tracer transport through the porous baffles. The flow through the porous medium is characterized while using the Darcy-Forchheimer relationship. Large Eddy Simulation (LES) model is used to simulate the instantaneous mixing of the tracer in the chambers of the contact tank. Three different porosities are considered to evaluate the effect of porosity on the hydraulic and mixing efficiencies of the contact tank. Simulated time-averaged flow field shows that porous baffles that are placed at the entrance of each chamber could successfully mitigate short-circuiting and yield plug-flow conditions through the system for low porosities. Flow in the contact tank becomes laminar as the flow velocities decrease due to viscous effects and inertial resistance in the porous zone. For this case, the tracer is transported with bulk flow through the system and leaves the contact tank with a high peak seen in the Residence Time Distribution (RTD) plot. Porous layer increases the hydraulic efficiency of the conventional design from “poor” to “good” according to the baffling factor and increases the overall efficiency from “compromising” to “good” according to the AD index. Comparison of the performance of the porous layer with the previously developed slot-baffle design shows that the slot-baffle design increases the efficiency of the tank with increasing dispersion effects, whereas the porous design increases hydraulic efficiency and reduces the dispersion effects. While the porous design reduces energy efficiency by 33% due to a drastic increase in drag in the flow through porous zone, the slot-baffle design increases the energy efficiency of the conventional design by 67%.
In this study, a perforated baffle design is proposed to improve mixing in contact tanks. Turbulent flow through the perforated baffle is studied at the perforation hole scale. The contribution of jets emerging from the perforations to the mixing process is evaluated in terms of standard mixing indexes for various perforation parameters, such as the solidity ratio and hole diameter. Based on numerical simulation results, the two sets of perforated baffles that yielded the highest performance were manufactured from polycarbonate and tracer studies were conducted on a laboratory model. Comparison of numerical and experimental results demonstrates that the numerical model developed is reliable in simulating the flow through the perforated baffles and the associated mixing level in the contact tank. Numerical simulations indicate that the jet flow structure through the perforated baffle penetrates to the recirculation zones in the neighboring chambers and turns the dead zones into active mixing zones. Furthermore, large scale turbulent eddies shed by the perforations contribute to the mixing process in the chambers of the tank. With the use of the perforated baffle design, it is shown that the hydraulic efficiency of the tank can be improved from average to superior according to the baffling factor, and the associated mixing in the proposed design can be improved by 31% according to the Morrill index.
The mixing and disinfection performance of a full-scale chlorine contact tank (CCT) is thoroughly investigated by means of numerical simulations for seasonal water supply variations in the water treatment plant (WTP) of Eskisehir in Turkey. Velocity measurements and tracer studies are carried out on a 1:10 scale laboratory model of the CCT to validate the numerical model. A good agreement between numerical and experimental results shows that the numerical model developed can be reliably used for the simulation of turbulent flow and solute transport in the full-scale CCT. Tracer studies indicate that the hydraulic performance of the CCT is classified as “average” according to the baffling factor, while the Morrill, Aral-Demirel (AD), and dispersion indexes indicate low mixing due to the recirculating and short-circuiting effects inside the chambers of the CCT. With respect to the first order modeling of chlorine decay and pathogen inactivation, chlorine concentrations are found to be significantly distinct for seasonal variations in water supply to maintain 3-log inactivation of Giardia cysts. A recently developed and patented slot-baffle design (SBD) is then applied to the full-scale CCT. It is found that the hydraulic efficiency of the CCT is improved to “high” and the Morrill index approaches 2, which identifies the system as a perfect mixing tank. Using the SBD, the chlorine demand has been successfully decreased by 19% while providing equivalent inactivation level. The novel SBD design also reduces energy loses in the turbulent flow through the tank and increases the energy efficiency of the CCT by 62%, which is significant for energy considerations in modern cities.
Vortical flow formed by a submerged hydraulic jump may produce significant hydrodynamic lift and drag pressures on a gate beneath the hydraulic jump. In this study, an experimental setup equipped with multi-pressure sensors was used to measure fluctuating impact pressures on the submerged gate for different flow conditions characterized by the inlet Froude number and submergence factor (S). Time-averaged and instantaneous pressure coefficients are evaluated based on simultaneous measurements of wall pressures at multiple locations, including those at the lip and downstream face of the gate. In particular, instantaneous lift pressure coefficients are observed to be independent of the submergence ratio for S > 0.6. It is found that low Froude number flows produce high surface pressure fluctuations and the dominant frequency of pressure fluctuations shifts to higher frequency as the Froude number increases. Pressure measurements for the free hydraulic jump suggest that the power spectra of lift pressure fluctuations are devoid of any significant energy level, whereas the resulting power spectra of the submerged flow exhibits significant energy level in the frequency range of 14-19 Hz. The proposed measurement system can be used for the in situ identification of hydrodynamic pressures acting on the gates in irrigation canals.
22 December 2024 in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
Çanakkale Onsekiz Mart Üniversitesi Terzioğlu Kampüsü'nde gerçekleştirilen bu çalışma, kampüs alanında Sünger Şehir konseptinin uygulanabilirliğini araştırmayı amaçlamaktadır. Çalışma kapsamında mevcut duruma yönelik saha araştırmaları yapılmış ve coğrafi bilgi sistemi ortamı kullanılarak sayısal veriler elde edilmiştir. Elde edilen bulgulara göre, mevcut durumda yapılacak değişiklikler ile yerleşkenin sünger şehir konseptine yaklaştırılması mümkündür. Bu değişiklikler arasında yeşil çatı uygulamaları, geçirimsiz yüzeylerin geçirgen hale getirilmesi ve mevcut yağmur suyu drenaj sisteminin iyileştirilmesi yer almaktadır. Ayrıca, kampüs içinde yağmur bahçeleri ve yağmur suyu biriktirme haznelerinin inşa edilmesi önerilmiştir. Bu uygulamaların hayata geçirilmesi, kampüsün su kaynaklarını daha verimli kullanmasını sağlayarak çevresel sürdürülebilirliği artıracaktır. Çalışma sonucunda, Sünger Şehir konseptinin kampüs içerisinde uygulanmasının mümkün olduğu ve belirlenen alanlarda yapılacak iyileştirmelerin bu süreci destekleyeceği tespit edilmiştir. Bu tür yeşil uygulamaların, kampüsün ekolojik ayak izini azaltacağı, yağmur suyunu etkili bir şekilde biriktireceği ve iklim değişikliği ile mücadelede önemli bir rol oynayacağı sonucuna varılmıştır.
1 January 2020 in Pamukkale University Journal of Engineering Sciences