The effect of talc in the two mixtures with the representative sample of fly ash (Class F) was investigated at sintering temperatures of 1000, 1100, and 1200 °C. X-ray diffraction, thermal DTA/TGA, and mercury intrusion porosimetry analyses were applied to characterize the mineral phase transformation of talc and fly ash in cordierite ceramic. The influence of iron oxide on talc transformation to Fe-enstatite was verified by the simulated molecular models and calculated XRD patterns and the assumption of Fe-cordierite crystallization was confirmed. The fly ash mixtures with 10 mass% of talc in comparison with 30 mass% of talc at 1000 °C and 1100 °C showed higher linear shrinkage and lower porosity. At a temperature of 1200 °C, sintering expansion and larger pores in mullite and cordierite ceramics also containing sapphirine and osumilite demonstrated that magnesium in FA and Tc structure did not react with the other constituents to form crystalline cordierite. The ceramics produced in the present work using fly ash and talc have similar properties to the commercial ceramics produced at sintering temperatures higher than 1250 °C.
1 March 2003 in Journal of Thermal Analysis and Calorimetry
Diclofenac (DC) and ibuprofen (IBU) are widely prescribed non-steroidal anti-inflammatory drugs, the consumption of which has rapidly increased in recent years. The biodegradability of pharmaceuticals is negligible and their removal efficiency by wastewater treatment is very low. Therefore, the beidelitte (BEI) as unique nanomaterial was modified by the following different surfactants: cetylpyridinium (CP), benzalkonium (BA) and tetradecyltrimethylammonium (TD) bromides. Organobeidellites were tested as potential nanosorbents for analgesics. The organobeidellites were characterized using X-ray powder diffraction (XRD), Infrared spectroscopy (IR), Thermogravimetry and differential thermal analysis (TG/DTA) and scanning microscopy (SEM). The equilibrium concentrations of analgesics in solution were determined using UV-VIS spectroscopy. The intercalation of surfactants into BEI structure was confirmed both using XRD analysis due to an increase in basal spacing from 1.53 to 2.01 nm for BEI_BA and IR by decreasing in the intensities of bands related to the adsorbed water. SEM proved successful in the uploading of surfactants by a rougher and eroded organobeidellite surface. TG/DTA evaluated the decrease in dehydration/dehydroxylation temperatures due to higher hydrophobicity. The Sorption experiments demonstrated a sufficient sorption ability for IBU (55–86%) and an excellent ability for DC (over 90%). The maximum adsorption capacity was found for BEI_BA-DC (49.02 mg·g−1). The adsorption according to surfactant type follows the order BEI_BA > BEI_TD > BEI_CP.
The recovery of zinc from mixed steelmaking and blast furnace sludge was investigated through a direct comparison of the hydrometallurgical acetic acid leaching process and pyrometallurgical processing using coke dust as a reductive agent, with particular emphasis on the structure and functional properties of the resulting ZnO products. The mixed sludge contained 9.71 wt.% ZnO, with zinc occurring predominantly in the form of stable ferritic phases, mainly franklinite ((ZnFeII)Fe2O4). Hydrometallurgical treatment using 1 mol·dm−3 acetic acid resulted in only a limited relative decrease in Zn content (16.8%) based on solid-phase concentrations, as mainly readily soluble zinc phases were dissolved, while ferrite-bound zinc remained largely unaffected. In contrast, pyrometallurgical treatment of the sludge–coke dust mixture at 1200 °C enabled highly effective zinc volatilization, reducing the residual Zn content below 0.05 wt.% and resulting in a relative decrease in Zn content of 99.5% based on solid-phase concentrations. Characterization by XRD, FTIR, SEM, and EDS revealed substantial differences between the products obtained by the two processing routes. The pyrometallurgically prepared ZnO-rich product exhibited higher crystallinity, well-developed rod-like morphology, and substantially lower Fe and Pb contamination than the hydrometallurgically prepared material. In contrast, the hydrometallurgical product showed lower crystallinity and elevated Fe and Pb contents and therefore represented a highly contaminated ZnO-rich oxide mixture. Photocatalytic tests using Rhodamine B showed measurable but low activity of the pyrometallurgical product, with approximately 18% degradation after 120 min of UV irradiation, whereas the hydrometallurgical product was practically inactive. Overall, carbothermic treatment provided substantially more effective Zn removal than acetic acid leaching, although the recovered ZnO-rich product exhibited only limited photocatalytic activity.