B. Tien-Long

B. Tien-Long


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 March 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TTThi-Hong Tran
Thi-Hong Tran
Le Xuan HungLe Xuan Hung
Le Xuan Hung
QNQuoc-Tuan Nguyen
Quoc-Tuan Nguyen
HLHong-Ky Le
Hong-Ky Le
HDHoang Tien Dung
Hoang Tien Dung
NVNgoc Pi Vu
Ngoc Pi Vu
This paper shows an optimization study on calculating the optimum replaced wheel diameter in internal grinding of stainless steel. In this work, the effects of the input factors, including the initial diameter, the grinding wheel width, the ratio between the length and the diameter of the work-pieces, the dressing depth of cut, the wheel life and the radial grinding wheel wear per dress on the optimum replaced grinding wheel diameter were considered. Also, the effects of cost components, including the cost of the grinding machine and the wheel cost were examined. Moreover, to estimate the influences of these parameters on the optimum replaced diameter, a simulation experiment was given and conducted by programming. From the results of the study, a regression equation was proposed to calculate the optimum replaced diameter.

26 November 2018 in Metals
Verified
Journal Article
Open access
PDF file
Thi Bich MacThi Bich Mac
Thi Bich Mac
VDVan-Chien Dinh
Van-Chien Dinh
BTB. Tien-Long
B. Tien-Long
Duc-Toan NguyenDuc-Toan Nguyen
Duc-Toan Nguyen
This paper investigates cutting force in thermal-assisted machining (TAM) by induction heating for SKD11 tool steel which is widely used in the mold industry. Experimental studies were first conducted at room and elevated temperatures to evaluate the effectiveness of the heating process on chip morphology and the cutting forces during the thermal-assisted machining and comparing with conventional machining method. The Taguchi method based on orthogonal array and analysis of variance ANOVA method was then used to design the number of experiments and evaluate the influence of cutting speed, feed rate, cutting depth, and elevated temperature on the cutting force. Study results showed a decrease in the cutting force in the TAM process. The optimal condition of parameters obtained for thermal-assisted machining were cutting speed 280 m/min, feed rate 230 mm/min, cutting depth 0.5 mm and temperature 400 °C. Finally, a proposed equation was established to determine the cutting force that was presented as a function of elevated temperatures when milling SKD11 material. A proposed cutting force model was compared, evaluated and confirmed to be in good agreement with experimental results.

16 April 2019 in Metals
Verified
Journal Article
Open access
PDF file
TTThi-Hong Tran
Thi-Hong Tran
Luu Anh TungLuu Anh Tung
Luu Anh Tung
QNQuoc-Tuan Nguyen
Quoc-Tuan Nguyen
HLHong-Ky Le
Hong-Ky Le
NTNguyen Anh Tuan
Nguyen Anh Tuan
NVNgoc Pi Vu
Ngoc Pi Vu
Based on a cost analysis, a method of identifying and predicting optimum replaced grinding wheel diameter (De.op) in a surface grinding operation for 9CrSi steel material was developed in this study. The De.op value was determined by minimizing the cost function. An experimental design was set up, and a computational program was developed to perform the experiment in order to calculate the De.op value. Furthermore, the impact of the grinding process parameters such as the initial grinding wheel diameter, the grinding wheel width, the total dressing depth, the Rockwell hardness of the workpiece, the radial grinding wheel wear per dress, and the wheel life on the De.op value were investigated. Moreover, the impacts of the cost components such as the machine tool hourly rate and the grinding wheel cost on the De.op value were given. Based on that, a mathematical model was proposed to determine the De.op value. The predicted De.op value was also verified by an experiment. The obtained result shows that the difference between the experimental De.op value and the predicted De.op value is within 1.7%, indicating that the mathematical model proposed in the study is reliable.

28 February 2015 in Science Editing
Verified
Journal Article
Open access
PDF file
BTB. Tien-Long
B. Tien-Long
Duc-Toan NguyenDuc-Toan Nguyen
Duc-Toan Nguyen
Vietnam is on its way to becoming a more developed country and more integrated into the global community. One of the most important key factors for development is science and technology. Scientific publications bring the most up-to-date information to scientists, researchers, and society. The quality of Vietnam’s scientific journals should be increased to international level. Also, the number of high quality articles published in international journals from Vietnam is limited compared to the number of researchers in Vietnam. There is still no Vietnamese journal indexed in Web of Science up to January 2015; while, three journals has been indexed in Scopus. This article discusses the current scenario of scientific and technological journals in Vietnam and the trend of development to international level

30 September 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Ivan A. ParinovIvan A. Parinov
Ivan A. Parinov
BTB. Tien-Long
B. Tien-Long
Shun-Hsyung ChangShun-Hsyung Chang
Shun-Hsyung Chang
Hung-Yu WangHung-Yu Wang
Hung-Yu Wang
Advanced materials and composites can be applied in a number of ways not only in modern science, techniques and technologies but in everyday life, including in the fields of aviation, medicine, waste reprocessing or the study of the underwater world