Dong-Kyu Kim

Prof. Dong-Kyu Kim

Ulsan University, Ulsan, South Korea

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 February 2021 in Metals
Verified
Journal Article
Open access
PDF file
TTTien Tran
Tien Tran
ZSZhengtong Shan
Zhengtong Shan
HLH. W. Lee
H. W. Lee
Dong-Kyu KimDong-Kyu Kim
Dong-Kyu Kim
In the present study, we propose a novel method of varying blank holding force (BHF) with the segmental blank holder and investigated its influence on the earing reduction in the circular deep drawing process of an aluminum alloy sheet. Based on the analysis of cup height profile, the principle of varying BHF using segmental blank holder was presented and analyzed by analytical theory and numerical simulation. The optimal varying BHF was reasonably determined and compared by using the analytical model and deep neural network (DNN) model integrated with genetic algorithm (GA). The integrated DNN-GA model revealed an accurate prediction and optimization of varying BHF for the minimum earing height variation, which showed a superior result to the analytical model. The optimal varying BHF exhibited a significant influence on the earing formation, resulting in the noticeable decrease of earing height variation. For volume consistency, it was found that an increase in thickness at the cup wall region predicted with the optimal varying BHF was achieved in the transverse direction, which implies an improvement of deep-drawability. Such results indicate that the varying BHF is more reasonable and effective than the uniform BHF. Furthermore, the material properties of the blank sheet also affected the reduction of earing in the deep drawing with varying BHF. The present study revealed that the lower the material strength, the more significant the earing reduction in the deep drawing with varying BHF will be.

15 May 2024 in Materials
Verified
Journal Article
Open access
PDF file
Huai WangHuai Wang
Huai Wang
HLH. W. Lee
H. W. Lee
MTMinh Tien Tran
Minh Tien Tran
Dong-Kyu KimDong-Kyu Kim
Dong-Kyu Kim
In this study, we investigated the micromechanical deformation and damage behavior of commercially extruded and additively manufactured 316L stainless steels (AMed SS316L) by combining experimental examinations and crystal plasticity modeling. The AMed alloy was fabricated using the laser powder bed fusion (LPBF) technique with an orthogonal scanning strategy to control the directionality of the as-fabricated material. Optical microscopy and electron backscatter diffraction measurements revealed distinct grain morphologies and crystallographic textures in the two alloys. Uniaxial tensile test results suggested that the LPBFed alloy exhibited an increased yield strength, reduced elongation, and comparable ultimate tensile strength in comparison to those of the extruded alloy. A microstructure-based crystal plasticity model was developed to simulate the micromechanical deformation behavior of the alloys using representative volume elements based on realistic microstructures. A ductile fracture criterion based on the microscopically dissipated plastic energy on a slip system was adopted to predict the microscopic damage accumulation of the alloys during plastic deformation. The developed model could accurately predict the stress–strain behavior and evolution of the crystallographic textures in both the alloys. We reveal that the increased yield strength in the LPBFed alloy, compared to that in the extruded alloy, is attributed to the higher as-manufactured dislocation density and the cellular subgrain structure, resulting in a reduced elongation. The presence of annealing twins and favorable texture in the extruded alloy contributed to its excellent elongation, along with a higher hardening rate owing to twin–dislocation interactions during plastic deformation. Moreover, the grain morphology and defect state (e.g., dislocations and twins) in the initial state can significantly affect strain localization and damage accumulation in alloys.

5 September 2019 in Materials
Verified
Journal Article
Open access
PDF file
HLH. W. Lee
H. W. Lee
KYKwang Jae Yoo
Kwang Jae Yoo
TTTien Tran
Tien Tran
IMIn Yong Moon
In Yong Moon
YOYoung-Seok Oh
Young-Seok Oh
Dong-Kyu KimDong-Kyu Kim
Dong-Kyu Kim
In the present study, we have investigated the effect of post-welding heat treatment (PWHT) of quenching and tempering (QT) on the microstructure and mechanical properties of welded boron steel joints processed using laser-arc hybrid welding on two commercial filler materials, SM80 (Type-I) and ZH120 (Type-II). The microstructure and mechanical properties of the weld joints were characterized via optical microscopy, Vickers microhardness, and the uniaxial tensile test. The macrostructure of the weld joint was composed of a fusion zone (FZ), heat-affected zone (HAZ), and base metal zone (BMZ). After the QT-PWHT, the QT specimens revealed the V-shape hardness distribution across the weld joint, while the as-welded specimen exhibited the M-shape hardness distribution. As a result, the QT specimens revealed the premature fracture with little reduction in the area at the interface between the HAZ and FZ, while the as-welded specimen exhibited the local necking and rupture in the BMZ. In addition, the Type-II filler material with a greater value of equivalent carbon content was rarely influenced by the tempering, maintaining its hardness in the as-quenched status, while the Type-I filler material showed a gradual decrease in hardness with the tempering time. The results demonstrate that the Type-II weld joint outperformed the Type-I weld joint in terms of the structural integrity of welded parts.

26 April 2024 in Metals
Verified
Journal Article
Open access
PDF file
Huai WangHuai Wang
Huai Wang
HLH. W. Lee
H. W. Lee
SKSeong-Hoon Kang
Seong-Hoon Kang
Dong-Kyu KimDong-Kyu Kim
Dong-Kyu Kim
Different ageing treatments have been developed to achieve targeted properties in aluminum alloys through altering microstructures. However, there is a lack of understanding regarding the effect of ageing treatments on the formability of these alloys. In this study, we employed crystal plasticity finite element (CPFE) modeling, in conjunction with the Marciniak-Kuczynski (M-K) approach, to investigate the effects of ageing treatments on the mechanical properties and formability of AA6061 aluminum alloy. The as-received sheet was in the T6 heat treatment state, which was subjected to artificial ageing and pre-ageing, respectively, to achieve two age-hardened alloys with modified precipitation states. The microstructures and crystallographic textures of the three alloys were measured using the electron backscattering diffraction (EBSD) technique, and uniaxial tensile tests were performed along the rolling direction (RD), transverse direction (TD), and diagonal direction (DD, 45° to the RD) for each alloy. The forming limit curve (FLC) of the as-received alloy was determined using the Nakazima test. The dependence of mechanical strength, tensile ductility, and work-hardening behavior on the ageing treatments was clarified. Then, the tensile test results were utilized to calibrate the modeling parameters used in the CPFE model, whereas the FLC predictability of the developed model was validated with the experimental one. In the formability analysis, the effects of the ageing treatment on the FLC exhibit a notable dependency on loading paths, and the pre-aged alloy exhibits better formability than the other two at the plane strain tension state, thanks to its high work-hardening levels. In addition, the deformed textures along the different loading paths and the effects of the initial texture on the FLC are also discussed.

30 April 2020 in Journal of Mechanical Science and Technology
Verified
Journal Article
Closed access
PDF file
HWHuai Wang
Huai Wang
Dong-Kyu KimDong-Kyu Kim
Dong-Kyu Kim
WWWanchuck Woo
Wanchuck Woo
SCShi-Hoon Choi
Shi-Hoon Choi
SLSoo Yeol Lee
Soo Yeol Lee
SHSun-Kwang Hwang
Sun-Kwang Hwang

25 August 2021 in Metals
Verified
Journal Article
Open access
PDF file
BCByung-Jin Choi
Byung-Jin Choi
IMIn Yong Moon
In Yong Moon
YOYoung-Seok Oh
Young-Seok Oh
SKSeong-Hoon Kang
Seong-Hoon Kang
SKSe-Jong Kim
Se-Jong Kim
HLH. W. Lee
H. W. Lee
In this paper, the extrusion process of titanium seamless tubes was studied using several finite element (FE) analyses. First, the finite element result was compared with experimental extrusion data acquired to validate the current analysis. Then, the effect of design parameters of the die shape was numerically analyzed using commercial FE software, Forge NxT, for the metal forming process. Elastic FE analyses were also conducted for dies to analyze the maximum principal stress that affects the early fracture of dies during the extrusion process and the maximum von Mises stress that causes the severe deformation of dies. Consequently, the effect of the corner radius at the exit and land length on the extrusion load and die stress is negligible compared to that of the corner radius at the entrance and die angle. Finally, we suggested a die angle of 60° and a corner radius at the die entrance between 10 and 15 mm as an optimal design for the current extrusion process.