Arameh Eyvazian

Dr. Arameh Eyvazian

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 March 2020 in Journal of Sandwich Structures & Materials
Verified
Journal Article
Closed access
PDF file
AEArameh Eyvazian
Arameh Eyvazian
MMMajid Moeinifard
Majid Moeinifard
FMFarayi Musharavati
Farayi Musharavati
STSeyedahmad Taghizadeh
Seyedahmad Taghizadeh
EMElsadig Mahdi
Elsadig Mahdi
TTTrong Nhan Tran
Trong Nhan Tran
This paper reports the mechanical behavior of resin pin-reinforced composite sandwich panels made from polyvinyl chloride core and glass/epoxy face sheets under indentation of a hemispherical indenter and three-point bending loading conditions. The goal was to study the effects of reinforcing parameters such as the number, arrangement, and diameter of the through-the-thickness resin pins on the indentation maximum load, the bending strength, and energy absorption characteristics of the tested samples under these loading conditions. The results revealed that using the resin pins to reinforce the polyvinyl chloride foam core led to increase the indentation maximum load up to 47%, and the maximum bending load up to 34%, compared to nonreinforced foam–core sandwich structures. Also, the presence of resin pins led to the change in the failure modes of specimens (i.e. from local to global deformation and failure) and consequently increased the energy absorption capability of sandwich structures by 31% and 68% respectively under indentation and bending loads.

25 December 2019 in Journal of Sandwich Structures & Materials
Verified
Journal Article
Open access
PDF file
AEArameh Eyvazian
Arameh Eyvazian
STSeyedahmad Taghizadeh
Seyedahmad Taghizadeh
Abdel Magid HamoudaAbdel Magid Hamouda
Abdel Magid Hamouda
FTFaris Tarlochan
Faris Tarlochan
MMMajid Moeinifard
Majid Moeinifard
MGMassimiliano Gobbi
Massimiliano Gobbi
Buckling and crushing behavior of foam-core hybrid composite sandwich columns under edgewise compressive load is dealt in this study. Composite laminates with different stacking sequence configurations made of glass and Dyneema-woven fabrics and AL 2024-T3 sheets were used in combination of polyvinyl chloride foam core to manufacture the specimens. Effects of face sheet thickness and stacking sequence configuration, slenderness ratio, boundary conditions, and sandwich reinforcement with through-thickness resin pins on the buckling and crushing behavior of the specimens were investigated. The results revealed that using the resin pins changes the unstable Euler buckling mode to a more stable progressive end-crushing and significantly increases the buckling load, specific buckling load, and energy absorption capability, which are highly favorable. Also, the results showed that in the specimens with fiber metal laminates, the major failure modes are face sheet-core debonding and face sheet delamination. However, based on the results, specimen with hybrid face sheets made from Dyneema fabrics and aluminum plates has the highest buckling load as well as the highest specific buckling load. Also, a specific fixture was designed to laterally clamp the sandwich column which causes a reduction in the probability of specimen end-crushing and significantly increases the buckling load.

9 March 2021 in International Journal of Crashworthiness
Verified
Journal Article
Closed access
AEArameh Eyvazian
Arameh Eyvazian
HTHossein Taghipoor
Hossein Taghipoor
TTTrongNhan Tran
TrongNhan Tran
In the present research, the crushing response and crashworthiness characteristics of aluminum circular tubes with and without vertical corrugations were studied. In this regard, crashworthiness characteristics and collapsing behaviors of these structures are analyzed. The tubes of higher diameter under quasi-static axial compression show greater values of crashworthiness indexes compared with those of the tubes with smaller diameter, except SEA of a small tube with 6 vertical corrugations. The energy absorption capacity is enhanced by the combination between small diameter and the number of vertical corrugations. The peak force of the vertically corrugated tubes is greater than that of non-corrugated ones; however, their force-displacement curves are smoother. The influence of the number of vertical corrugations on the crashworthiness performance is studied. An analytical relationship is developed for mean force based on the experimental results and the ‘plastic hinge line’ concept. A comparison of the analytical results with the experimental ones indicates the reasonable accuracy of the analytical models. Improved Technique of Order Preference by Similarity to Ideal Solution (ITOPSIS) is employed to select the best structure for energy absorption purposes.

1 October 2021 in Structures
Verified
Journal Article
Closed access
SKSamira Khodabakhshpour-Bariki
Samira Khodabakhshpour-Bariki
RJRamazan-Ali Jafari-Talookolaei
Ramazan-Ali Jafari-Talookolaei
MAMostafa Attar
Mostafa Attar
AEArameh Eyvazian
Arameh Eyvazian

15 September 2021 in The European Physical Journal Plus
Verified
Journal Article
Closed access
PDF file
AEArameh Eyvazian
Arameh Eyvazian
CZChunwei Zhang
Chunwei Zhang
FMFarayi Musharavati
Farayi Musharavati
AFAshkan Farazin
Ashkan Farazin
MMMehdi Mohammadimehr
Mehdi Mohammadimehr
AKAfrasyab Khan
Afrasyab Khan

31 August 2021 in Archives of Civil and Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
CZChunwei Zhang
Chunwei Zhang
LWLimin Wang
Limin Wang
AEArameh Eyvazian
Arameh Eyvazian
AKAfrasyab Khan
Afrasyab Khan
TSTamer A. Sebaey
Tamer A. Sebaey
NFNaeim Farouk
Naeim Farouk