Majid Moeinifard

Majid Moeinifard

Auto-generated profile, based on publicly available information

Majid Moeinifard

Tarbiat Modares University

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 December 2019 in Journal of Sandwich Structures & Materials
Verified
Journal Article
Open access
PDF file
AEArameh Eyvazian
Arameh Eyvazian
STSeyedahmad Taghizadeh
Seyedahmad Taghizadeh
Abdel Magid HamoudaAbdel Magid Hamouda
Abdel Magid Hamouda
FTFaris Tarlochan
Faris Tarlochan
MMMajid Moeinifard
Majid Moeinifard
MGMassimiliano Gobbi
Massimiliano Gobbi
Buckling and crushing behavior of foam-core hybrid composite sandwich columns under edgewise compressive load is dealt in this study. Composite laminates with different stacking sequence configurations made of glass and Dyneema-woven fabrics and AL 2024-T3 sheets were used in combination of polyvinyl chloride foam core to manufacture the specimens. Effects of face sheet thickness and stacking sequence configuration, slenderness ratio, boundary conditions, and sandwich reinforcement with through-thickness resin pins on the buckling and crushing behavior of the specimens were investigated. The results revealed that using the resin pins changes the unstable Euler buckling mode to a more stable progressive end-crushing and significantly increases the buckling load, specific buckling load, and energy absorption capability, which are highly favorable. Also, the results showed that in the specimens with fiber metal laminates, the major failure modes are face sheet-core debonding and face sheet delamination. However, based on the results, specimen with hybrid face sheets made from Dyneema fabrics and aluminum plates has the highest buckling load as well as the highest specific buckling load. Also, a specific fixture was designed to laterally clamp the sandwich column which causes a reduction in the probability of specimen end-crushing and significantly increases the buckling load.

5 March 2020 in Journal of Sandwich Structures & Materials
Verified
Journal Article
Closed access
PDF file
AEArameh Eyvazian
Arameh Eyvazian
MMMajid Moeinifard
Majid Moeinifard
FMFarayi Musharavati
Farayi Musharavati
STSeyedahmad Taghizadeh
Seyedahmad Taghizadeh
EMElsadig Mahdi
Elsadig Mahdi
TTTrong Nhan Tran
Trong Nhan Tran
This paper reports the mechanical behavior of resin pin-reinforced composite sandwich panels made from polyvinyl chloride core and glass/epoxy face sheets under indentation of a hemispherical indenter and three-point bending loading conditions. The goal was to study the effects of reinforcing parameters such as the number, arrangement, and diameter of the through-the-thickness resin pins on the indentation maximum load, the bending strength, and energy absorption characteristics of the tested samples under these loading conditions. The results revealed that using the resin pins to reinforce the polyvinyl chloride foam core led to increase the indentation maximum load up to 47%, and the maximum bending load up to 34%, compared to nonreinforced foam–core sandwich structures. Also, the presence of resin pins led to the change in the failure modes of specimens (i.e. from local to global deformation and failure) and consequently increased the energy absorption capability of sandwich structures by 31% and 68% respectively under indentation and bending loads.

22 January 2023 in Advanced Composite Materials
Verified
Journal Article
Closed access
ATAli Talezadehlari
Ali Talezadehlari
MMMajid Moeinifard
Majid Moeinifard
We comment on the paper published by Sakata et al., in J. Adv. Compos. Mater., 2018, 27, 35–51, which was in continuation of the previous work by Sakata and Ben in J. Adv. Compos. Mater., 2012, 21, 445–457. Although the experimental section in both works were identical, the reported numerical values of the linear buckling loads differed. In addition, all the specimens were manufactured using an identical process by employing silicone rubber mold and filament winding technique, and outer skin layers and stiffeners consisted of a fixed number of plies. Nonetheless, different shell thicknesses and stiffeners cross-sectional areas were reported for the specimens. Since the buckling behavior of cylindrical shells is highly sensitive to their thickness, the difference in the reported numerical linear buckling loads of the mentioned studies could be due to different thickness values used as inputs for their numerical analyses. In order to address this subject, the present study aimed to provide complete and comprehensive data on the buckling behavior of unstiffened and grid-stiffened cylindrical shells with the same material properties and geometrical dimensions but various thicknesses. The presented results can be used as a benchmark for future studies.