This article presents a configuration of Variable Speed Wind Energy Conversion System consisting of a Permanent-Magnet Synchronous Generator (PMSG-based VSWECS) through a Vienna rectifier. The motivation for this topology is to make the system more reliable, power efficient, cost-effective and simple to control. The newly proposed current control topology with an addition of low pass filter provides the ability to improve power factor and distortion of line current. The considered system consists of a wind turbine coupled with a direct drive PMSG via Vienna rectifier and it's simple current control scheme. It's control strategy has been simulated to get DC link voltage from variable wind energy. In this article, the effects of Vienna rectifier with PMSG have been studied and simulated using MATLAB/Simulink. Simulation results ratify the performance of proposed topology.
In the modern shipboard power system, there is a growing concern about reduced fuel economy, efficiency improvement, and minimized emission in recent years. Besides, considering the islanded nature of the shipboard power system, ensuring the system reliability at both generation and load side is crucial. In this context, a hybrid medium voltage DC (MVDC) distribution system concept with diesel engine, PV system, and battery energy storage system (BESS) as the generators for the shipboard power system is proposed. Variable speed operation of a diesel engine is considered for the benefit of minimal specific fuel oil consumption (SFOC). Regarding the fault-tolerant characteristics of six-phase permanent magnet synchronous machine (PMSM), it is used for both generating and motoring application, thus maintaining system reliability at any time. A hierarchical control system is designed and implemented to ensure proper load power-sharing among the generators and to regulate the dc-link voltage of the proposed MVDC distribution system. To bolster the intent of minimal SFOC zone operation of diesel engines and coordination between the generators and load, a deterministic rule-based power management system is proposed and implemented. The simulation is carried out for potential operational modes of a cruise ship in the MATLAB/Simulink environment. Simulation results show that the proposed topological and control structure has satisfactory performance in terms of power delivery, stable dc-link dynamics, and overall system stability.
Modern multi-MW wind generators have used multi-level converter structures as well as parallel configuration of a back to back three-level neutral point clamped (3L-NPC) converters to reduce the voltage and current stress on the semiconductor devices. These configurations of converters for offshore wind energy conversion applications results in high cost, low power density, and complex control circuitry. Moreover, a large number of power devices being used by former topologies results in an expensive and inefficient system. In this paper, a novel bi-directional three-phase hybrid converter that is based on a parallel combination of 3L-NPC and ‘n’ number of Vienna rectifiers have been proposed for multi-MW offshore wind generator applications. In this novel configuration, total power equally distributes by sharing of total reference current in each parallel-connected generator side power converter, which ensures the lower current stress on the semiconductor devices. Newly proposed topology has less number of power devices compared to the conventional configuration of parallel 3L-NPC converters, which results in cost-effective, compact in size, simple control circuitry, and good performance of the system. Three-phase electric grid is considered as a generator source for implementation of a proposed converter. The control scheme for a directly connected three-phase source with a novel configuration of a hybrid converter has been applied to ratify the equal power distribution in each parallel-connected module with good power factor and low current distortion. A parallel combination of a 3L-NPC and 3L-Vienna rectifier with a three-phase electric grid source has been simulated while using MATLAB and then implemented it on hardware. The simulation and experimental results ratify the performance and effectiveness of the proposed system.
Grid-connected photovoltaic (PV) system has gained momentum at an exponential rate in recent years. Intermittent nature of PV system causing demand and generation mismatch in power is one major issue. Additionally, the quality of power supplied to the load and surplus power injected into the grid along with better dynamic performance are other two main issues of the grid-connected PV system. To address the problem of intermittency and dynamic performance we use battery energy storage (BES). Similarly, three-level neutral point clamped (NPC) inverter with LCL filter is used for better current and voltage waveforms to ensure the better-injected power quality. In this paper, PV array, boost converter, maximum power point tracking (MPPT) control, bidirectional converter, three-level NPC inverter, and their associated control system is designed and simulated in MATLAB/Simulink. The simulation results shows the injected current has 0.68% THD, faster system response, and generated power matches the load demand.
Power electronic converters are widely used in wind energy conversion system (WECS) applications. Therefore, with the increasing manufacturing capacity of multi-MW wind generators, multi-level converters, or parallel configuration of converters are becoming more attractive solutions towards DC collection from the wind generator. Among the multilevel converters, three-level full-scale neutral point diode clamped (3L-NPC) converter are using extensively for such applications in order to reduce the voltage stress on the semiconductor devices. In this article, a comparative study based on several devices used by NPC, capacitor clamped (CC) as well as Vienna rectifier has been done. Furthermore, their estimated cost comparison and complexity of control switches have been debated. By keeping in view the merits and demerits of these rectifiers, a low cost three-level active rectifier having a smaller number of active switches with a simple control scheme have been implemented. Considering a three-phase electric grid as a generated source, a 2.2KW low-cost three-level Vienna rectifier is simulated using MATLAB/Simulink. DSP (TMS320F28335) based experimental results ratify the simulated circuit with THD<5%.