The paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are analyzed. The heat of the gas turbine engine exhaust gas is utilized in a thermo-chemical reactor and a steam generator. The engines operate on synthesis gas, which is obtained as a result of steam conversion of the associated gas. Criteria for evaluating the effectiveness of the developed schemes are proposed. The results of mathematical modeling of processes in a 14.1 MW diesel-gas turbine power plant with waste heat recovery are presented. The effect of the steam/associated gas ratio on the efficiency criteria is analyzed. The obtained results indicate relatively high effectiveness of the scheme with separate high and low pressure thermo-chemical reactors for producing fuel gas for both gas turbine and internal combustion engines. The calculated efficiency of such a power plant for considered input parameters is 45.6%.
Growing economies need green and renewable energy. Their financial development can reduce energy consumption (through energy-efficient technologies) and replace fossil fuels with renewable ones. Gas turbine engines are widely used in transport and industry. To improve their economic attractiveness and to reduce harmful emissions, including greenhouse gases, alternative fuels and waste heat recovery technologies can be used. A promising direction is the use of alcohol and thermo-chemical recuperation. The purpose of this study is to estimate the economic efficiency and carbon dioxide emissions of an alcohol-fueled regenerative gas turbine engine with thermo-chemical recuperation. The carbon dioxide emissions have been determined using engine efficiency, fuel properties, as well as life cycle analysis. The engine efficiency was maximized by varying the water/alcohol ratio. To evaluate steam fuel reforming for a certain engine, a conversion performance factor has been suggested. At the optimal water/methanol ratio of 3.075 this technology can increase efficiency by 4% and reduce tank-to-wake emission by 80%. In the last 6 months of 2019, methanol prices were promising for power and cogeneration plants in remote locations. The policy recommendation is that local authorities should pay attention to alcohol fuel and advanced turbines to curb the adverse effects of burning petroleum fuel on economic growth and the environment.
29 March 2018 in Journal of Marine Science and Application
Enlarging the fleet of gas carriers would make it possible to respond to the growing demand for hydrocarbon gases, but it will increase carbon dioxide emissions. The International Maritime Organization (IMO) has developed the energy efficiency design index (EEDI) with the objective of carbon emission reduction for new ships. In this paper, thirty gas carriers transporting liquefied natural gas (LNG) and liquefied petroleum gas (LPG) and equipped with various types of main engines are considered. As shown by the calculation of the attained EEDI, 2 of the 13 LPG carriers and 6 of the 17 LNG carriers under study do not comply with the EEDI requirements. To meet the stringent EEDI requirements, applying thermochemical regenerators (TCRs) fed by main engine exhaust gases is suggested. Mathematical modeling is applied to analyze the characteristics of the combined gas-turbine-electric and diesel-electric power plant with thermochemical recuperation of the exhaust gas heat. Utilizing TCR on gas carriers with engines fueled by syngas produced from boil-off gas (BOG) reduces the carbon content by 35% and provides the energy efficiency required by IMO without the use of other technologies.
In this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight ratio and efficiency for diesel and gas turbine power modules of various capacities. Mathematical modeling methods are used to analyze the parameters of an alternative gas turbine unit based on steam conversion of the associated gas, and the estimated efficiency of the energy module is shown to be 50%. In the modeling of the burning processes, the UGT 25000 serial low emission combustor is considered, and a detailed analysis of the processes in the combustor is presented, based on the application of a 35-reaction chemical mechanism. We confirm the possibility of efficient combustion of associated gas steam conversion products with different compositions, and establish that stable operation of the gas turbine combustor is possible when using fuels with low calorific values in the range 7–8 MJ/kg. It is found that the emissions of NOx and CO during operation of a gas turbine engine on the associated gas conversion products are within acceptable limits.
The perspectives of waste-heat recovery of low-speed diesel engines using metal-hydride units of continuous operation have been substantiated. The design scheme of a unit and parameters of operating environment have been described. The results of mathematical modeling of processes in a waste heat recovery metal-hydride unit have been represented. The work efficiency of a waste heat recovery metal-hydride unit as a part of a marine propulsion complex on the basis of a low-speed dual-fuel diesel engine has been revealed. The novelty of this study is the investigation of metal hydride technology for application in the gas fuel compressor drive of LNG-powered ships.