The effect of the transverse laser structure on two-photon absorption (TPA) related effects in high-power diode lasers is analysed theoretically. The direct effect of TPA is found to depend significantly on the transverse waveguide structure, and predicted to be weaker in broad and asymmetric waveguide designs. The indirect effect of TPA, via carrier generation in the waveguide and free-carrier absorption, is analysed for the case of a symmetric laser waveguide and shown to be strongly dependent on the active layer position. With the active layer near the mode peak, the indirect effect is weaker than the direct effect due to the population of TPA-created carriers being efficiently depleted by their diffusion and capture into the active layer, whereas for the active layer position strongly shifted towards the p -cladding, the indirect effect can become the dominant power limitation at very high currents. It is shown that for optimizing a laser design for pulsed high power operation, both TPA related effects and the inhomogeneous carrier accumulation in the waveguide caused by diffusive current need to be taken into account.
1 August 2022 in IEEE Photonics Technology Letters
A nanoscale 3D hybrid plasmonic waveguide (HPWG) refractive index-cum- temperature sensor has been proposed and simulated in this work. The aqueous analyte (benzene C 6 H 6 ) sensing is possible over the wavelength range from $1.18~\mu \text{m}$ to $2.2~\mu \text{m}$ . A well-known refractive index (RI) sensing method (or wavelength interrogation) is considered for the proposed Si-TiO 2 -SiO 2 -Au nanostructure. The sensor design includes, titanium dioxide (TiO 2 ) layer deposited over the silicon dioxide to enhance the overall sensitivity of the HPWG sensor. The finite element method (FEM) based 3D-numerical simulations are performed for an IR band signal, predicting 1022.75 nm/RIU device sensitivity and 2.95 nm/°C temperature sensitivity. The proposed sensor is suitable for next-generation on-chip biochemical sensing applications with nanoscale dimensions, low cost, and high sensitivity.
The effect of longitudinal spatial hole burning on the performance of a semiconductor laser with a strongly asymmetric resonator is investigated numerically. The effects of spatial hole burning on, firstly, the non-stimulated recombination in the laser (quantified as an increased effective threshold current) and, secondly, the output efficiency are calculated and compared, and the latter is shown to dominate at high currents. It is shown that the output efficiency at high pumping levels in the presence of the spatial hole burning effect can be estimated using the standard expression as the ratio of output loss to total loss, but with the internal loss enhanced by a factor greater than one and independent on the injection level. A simple universal expression for this factor for a highly asymmetric cavity, as a function of the output mirror reflectance, is obtained and compared to numerical results, with good agreement.
We analyze the thermal effects in carrier accumulation (leakage) in the optical confinement layer of high-power semiconductor lasers. The experimental data for the symmetric broadened-cavity lasers are analyzed to extract the information on the current dependence of the internal loss and laser temperature. These data are used to predict the thermal behavior and output power-current dependence of a proposed asymmetric nonbroadened construction operating at the same wavelength, and a significant improvement is predicted.
10 September 2019 in IEEE Photonics Technology Letters
We report first experimental results on a high-power pulsed semiconductor laser operating in the eye-safe spectral range (wavelength around 1.5 lm) with an asymmetric waveguide structure. The laser has a bulk active layer positioned very close to the p-cladding in order to eliminate current-induced nonuniform carrier accumulation in the p-side of the waveguide and the associated carrier losses. Moderate doping of the n-side of the waveguide is used to strongly suppress nonuniform carrier accumulation within this part of the waveguide. Highly p-doped InP p-cladding facilitates low series resistance. An as-cleaved sample with a stripe width of 90 lm exhibits an output power of about 18 W at a pumping current amplitude of 80 A. Theoretical calculations, validated by comparison to experiment, suggest that the performance of lasers of this type can be improved further by optimization of the waveguide thickness and doping as well as improvement of injection efficiency.
1 July 2020 in Semiconductor Science and Technology
It is shown, by calculations calibrated against the authors’ recent experimental data, that an eye-safe wavelength range InGaAsP/InP high pulsed power laser design using a bulk active layer, which has a large refractive index step with respect to the optical confinement layer and is located close to the p-cladding, can provide substantial performance improvement compared to the best results achieved so far for this operating regime and wavelength. The dependence of the laser performance on the design parameters such as the thicknesses of the active layer and the waveguide, as well as the cavity length, are analysed. It is shown that the relatively thick bulk active layer in such InGaAsP/InP lasers allows the use of short cavity lengths (∼1 mm or even shorter), for achieving high pulsed power while maintaining a low p-cladding series resistance (making for high efficiency) and a narrow far field (making for high brightness). A single-asymmetry structure with the asymmetric active layer location but symmetric optical confinement layer/cladding refractive index steps gives performance only marginally inferior to that of a double-asymmetric one including asymmetric refractive index steps.