Chongchong Tang

Dr. Chongchong Tang

Institute for Applied Materials (IAM), Karlsruhe Institute of Technology (KIT), Hermann- von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 December 2019 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Open access
PDF file
Chongchong TangChongchong Tang
Chongchong Tang
MSMartin Steinbrück
Martin Steinbrück
MKMichael Klimenkov
Michael Klimenkov
UJUte Jäntsch
Ute Jäntsch
HSHans Jürgen Seifert
Hans Jürgen Seifert
Michael StueberMichael Stueber
Michael Stueber
Mn + 1AXn (MAX; n = 1–3) phases are ternary layered nitride and carbide compounds featuring a combination of metallic and ceramic properties. Highly basal-plane textured and polycrystalline Cr2AlC, Ti2AlC, and Ti3AlC2 single-phase coatings have been synthesized on both amorphous and polycrystalline substrates via controlled thermal annealing of magnetron-sputtered nanoscale multilayers built by individual transition metal, carbon, and aluminum layers. Formation of substitutional solid solution carbide phases was triggered via solid-state diffusion reactions during annealing. Lower ordered Ti2AlC initially crystallized at an intermediate temperature range and was recognized as an intermediate reactant in the case of synthesizing the Ti3AlC2 312 MAX phase via annealing corresponding stoichiometric multilayers. The crystallization onset temperatures identified via in-situ high-temperature x-ray diffraction measurements were approximately 480, 660, and 820 °C for Cr2AlC, Ti2AlC, and Ti3AlC2, respectively. Contrary to the usually observed columnar structure representative of magnetron-sputtered coatings, the coatings synthesized via the current approach are composed of plateletlike, elongated crystallites. The nanoscale multilayered design stimulates the textured growth of MAX structures during thermal annealing. More specifically, the preferred crystallographic orientation relationships among the as-deposited transition metal layers, the intermediate solid solution phases, and the end-product MAX phases facilitate the growth of textured MAX phase films.

28 January 2022 in Coatings
Verified
Journal Article
Open access
PDF file
Chongchong TangChongchong Tang
Chongchong Tang
MSMartin Steinbrück
Martin Steinbrück
MGMirco Große
Mirco Große
SUSven Ulrich
Sven Ulrich
Michael StueberMichael Stueber
Michael Stueber
Elemental Cr/C/Al multilayers (stoichiometric ratio: 2:1:1) with and without a Cr overlayer have been synthesized on Zircaloy-4 substrates by magnetron sputtering. The effects of annealing temperatures (400 and 550 °C) on phase/microstructure formation, mechanical properties, and oxidation/corrosion performance have been comparatively studied. Annealing of the multilayers at 400 °C led to the formation of nanocrystalline composite consisting of intermetallic and binary carbide phases. Single-phase Cr2AlC was obtained after 550 °C annealing, but with microcracking of the coatings. Both annealed coatings displayed similar mechanical properties, high-temperature oxidation, and hydrothermal corrosion mechanisms. The composite coatings annealed at 400 °C significantly enhance the high-temperature oxidation resistance (α-Al2O3 scale growth) and hydrothermal corrosion (Cr2O3 passivation layer formation) of a Zircaloy-4 substrate without coating microcracking and delamination. Nanocomposite CrCAl-based coatings are promising candidates for coated ATF applications with acceptable processing temperatures and excellent oxidation/corrosion resistances for a zirconium alloy substrate.

31 January 2026 in High Temperature Corrosion of Materials
Verified
Journal Article
Open access
PDF file
FLF. Lanoy
F. Lanoy
EWEmma White
Emma White
BSB. Schäfer
B. Schäfer
Chongchong TangChongchong Tang
Chongchong Tang
CSCarsten Schroer
Carsten Schroer
MGMathias Galetz
Mathias Galetz
This study investigates the oxidation behavior of a binary Cr-20 at.%Ta alloy in a nitrogen-free, reduced oxygen partial pressure environment at 1000 °C for 48 h, aiming to clarify the intrinsic formation and growth mechanisms of protective (Cr, Ta)O 2 oxides. Chromium outward diffusion primarily governs oxidation, leading to a duplex scale with an outer Cr 2 O 3 layer and an inner (Cr,Ta)O 2 subscale. Two distinct (Cr, Ta)O 2 phases were identified: CrTaO 4 (rutile structure) in outer regions and CrTa 2 O 6 (trirutile structure) closer to the substrate, with CrTa 2 O 6 confirmed as thermodynamically more stable through post-oxidation heat treatment and calculations. Thermogravimetric analysis revealed the parabolic oxidation constant of Cr-20 at.%Ta for fine-grained samples was eight times lower than pure chromium, highlighting the beneficial effect of the (Cr, Ta)O 2 layer. The microstructure significantly influences the protectiveness: fine-grained alloys promoted a continuous (Cr, Ta)O 2 layer, leading to enhanced oxidation resistance, particularly after a transient period required for the protective subscale to establish. This research underscores the critical role of (Cr, Ta)O 2 and microstructure in developing advanced oxidation-resistant refractory alloys.

25 April 2023 in Applied Surface Science
Verified
Journal Article
Closed access
Chongchong TangChongchong Tang
Chongchong Tang
MDMichael Dürrschnabel
Michael Dürrschnabel
UJUte Jäntsch
Ute Jäntsch
MKMichael Klimenkov
Michael Klimenkov
MSMartin Steinbrück
Martin Steinbrück
MSMichael Stüber
Michael Stüber

25 July 2026 in High Temperature Corrosion of Materials
Verified
Journal Article
Open access
PDF file
BSBjörn Schäfer
Björn Schäfer
MDMichael Dürrschnabel
Michael Dürrschnabel
CSCarsten Schroer
Carsten Schroer
Chongchong TangChongchong Tang
Chongchong Tang
FLFabian Lanoy
Fabian Lanoy
BGBronislava Gorr
Bronislava Gorr
The oxidation behaviour of TaMoCrTiAl in steam at 900–1100 °C has been investigated by thermogravimetric analysis of oxidation kinetics and detailed cross-sectional SEM and TEM characterization of the multilayered oxide scales formed during exposure. Experiments point to the significance of both outward diffusion of metal cations and inward transport of oxidizing species, whereas the latter becomes increasingly dominant with increasing exposure times. Based on these findings, a mechanistic oxidation model for TaMoCrTiAl in steam is proposed and compared with the oxidation behaviour in air. In contrast to oxidation in synthetic air, the (Cr, Ta, Ti)O₂ layer typical for TaMoCrTiAl is absent, but formation of (Ti, Ta)O₂ observed, with impact on both formation of external oxide and internal corrosion.

5 December 2018 in arXiv
Verified
Preprint
Open access
PDF file
Chongchong TangChongchong Tang
Chongchong Tang
AJAdrian Jianu
Adrian Jianu
MSMartin Steinbrueck
Martin Steinbrueck
MGMirco Grosse
Mirco Grosse
AWAlfons Weisenburger
Alfons Weisenburger
HSHans Juergen Seifert
Hans Juergen Seifert
FeCrAl alloys are proposed and being intensively investigated as alternative accident tolerant fuel (ATF) cladding for nuclear fission application. Herein, the influence of major alloy elements (Cr and Al), reactive element effect and heating schedules on the oxidation behavior of FeCrAl alloys in steam up to 1500{\deg}C was examined. In case of transient ramp tests, catastrophic oxidation, i.e. rapid and complete consumption of the alloy, occurred during temperature ramp up to above 1200{\deg}C for specific alloys. The maximum compatible temperature of FeCrAl alloys in steam increases with raising Cr and Al content, decreasing heating rates during ramp period and doping of yttrium. Isothermal oxidation resulted in catastrophic oxidation at 1400{\deg}C for all examined alloys. However, formation of a protective alumina scale at 1500{\deg}C was ascertained despite partial melting. The occurrence of catastrophic oxidation seems to be controlled by dynamic competitive mechanisms between mass transfer of Al from the substrate and transport of oxidizing gas through the scale both toward the metal/oxide scale interface.